Atten ATM3500A Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 203

background image

VOLTage:DC

VOLTage:AC

VOLTage:DC:RATio

CURRent:DC

CURRent:AC

RESistance (for 2-wire ohms)

FRESistance (for 4-wire ohms)

FREQuency

PERiod

CONTinuity

DIODe TCOuple TEMPerature

[SENSe:]FUNCtion?

Query the measurement function and return a quoted string.

[SENSe:]<

function

>:RANGe {<

range

>|MINimum|MAXimum}

Select   a   range   for   the   selected   function.   For   frequency   and   period
measurements,   range   applies   to   the   signal’s   input   voltage,   not   its
frequency   (use   FREQuency:VOLTage   or   PERiod:VOLTage).   MIN   selects   the
lowest range for the selected function. MAX selects the highest range.

[SENSe:]<

function

>:RANGe? [MINimum|MAXimum]

Query the range for the selected function. For frequency and period, use
FREQuency:VOLTage or PERiod:VOLTage. Autorange thresholds: Down range
at <10% of range; Up range at >120% of range.

[SENSe:]<

function

>:RANGe:AUTO {OFF|ON}

Disable or enable autorange for the selected function.

[SENSe:]<

function

>:RANGe:AUTO?

Query the autorange setting. Return “1” (ON) or “0” (OFF).

[SENSe:]<

function

>:RESolution {<

resolution

>|MINimum|MAXimum}

Set resolution for the selected function (not valid for frequency, period, or
ratio). Specify the resolution in the same units as the measurement
function, not in number of digits. MIN selects the smallest value accepted,
which gives the most resolution. MAX selects the largest value accepted which
gives the least resolution.

[SENSe:]<

function

>:RESolution? [MINimum|MAXimum]

Query the resolution for the selected function.

[SENSe:]UNIT {Cel|Far|K}

Select units for temperature measurement. Cel means Celsius, Far means

158

«
...
156
157
158
159
160
...
»

Содержание ATM3500A












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATM3500A

Бренд: Keithley Страницы: 51

OBID i-scan ID ISC.ANT.MUX

Бренд: Feig Electronic Страницы: 37

Бренд: HoldPeak Страницы: 2

Бренд: Circuit-test Страницы: 14

Бренд: Maxwell Digital Multimeters Страницы: 13

Бренд: Greenlee Страницы: 72

Бренд: Greenlee Страницы: 48

Бренд: Greenlee Страницы: 84

Бренд: QEO Страницы: 32

Бренд: Gossen MetraWatt Страницы: 51

Бренд: twintex Страницы: 4

Бренд: UEi Страницы: 9

Бренд: Radio Shack Страницы: 24

Бренд: Hach Страницы: 8

Бренд: Hach Страницы: 96

Бренд: Keithley Страницы: 107

VersiVision FVRM880x

Бренд: Versitron Страницы: 12

VersiVision FDVR110x

Бренд: Versitron Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды