Associated Research HypotULTRA 7800 Скачать руководство пользователя | Manualshive

Страница: 140 / 206

background image

135

BUS REMOTE INTERFACE GPIB/USB/RS-232

This section provides information on the proper use and configuration of the bus
remote interface. The USB/RS-232 remote interface is standard on the HypotULTRA
but the GPIB (IEEE-488) interface option can be substituted for the USB/RS-232
interface. Please refer to

Section 10. Options

for details on the HypotULTRA

options.  The USB/RS-232 interface uses the same command set as the GPIB
interface for setting test parameters; however, many functions of the GPIB 488.2
interface are not available through USB/RS-232.  The IEEE-488 interface included
with the HypotULTRA conforms to the requirements of the IEEE-488.2 standard.

The USB/RS-232 interface card requires you to download a driver in order for the
instrument to recognize the USB interface. The driver can be found on the Associated
Research, Inc. website:

http://www.asresearch.com/products/software/USB-driver.aspx

Click on “USB/RS-232 Driver” to download the driver. This link contains an automatic
extract and install program. Follow the instructions of the installation program to
initialize the driver install. NOTE: The USB port acts as a USB to RS-232 converter.
As a result, the PC will recognize the USB port as a virtual COM port.

8.1 USB/RS-232 Interface

This interface provides all of the control commands and parameter setting commands
of the GPIB interface with the exception of some of the 488.2 Common Commands
and SRQ capability. All commands can be found in section

7.4. USB/RS-232/GPIB

Command List

. The identification command *IDN and the Status Reporting

commands are also available through USB/RS-232.

RS-232 Connector

The RS-232 cabling should be configured as follows for a 9-pin serial port interface:

Communications Port Configuration

The COM port should have the following configuration:

38400 baud

Instrument RS-232 Port

PC / Bus Controller

2

3

5

2

3

5

TD

RD

TD

RD

SIG
GND

SIG
GND

«
...
138
139
140
141
142
...
»

Содержание HypotULTRA 7800















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HypotULTRA 7800

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Бренд: Banner Страницы: 11

Бренд: Bante Instruments Страницы: 10

Бренд: BANTE Страницы: 11

Бренд: Banner Страницы: 14

Бренд: Banner Страницы: 16

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: QALCOMET Страницы: 52

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: Velleman Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды