Associated Research HypotULTRA 7800 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 206

background image

124

6.6

Error Messages

Abort:

This message appears on the display if you abort the test in process with the

RESET button or remote Reset control.

HI-Limit:

This message appears on the display if the DUT measurement exceeds the

HI-Limit setting of any parameter.

LO-Limit:

This message appears on the display if the DUT measurement drops below

the LO-Limit

Max-Lmt:

This message appears on the display if the DUT measurement exceeds the

Max-Lmt setting of any parameter.

Min-Lmt:

This message appears on the display if the DUT measurement drops below

the Min-Lmt.

CONT-Fail:

This message appears on the display if the DUT fails the basic continuity

check performed during an AC/DC Withstand

test (if Continuity is selected “ON”).

Arc-Fail:

This message appears on the display if the DUT arcing current exceeds the

Arc

Sense limit and Arc function is active (Arc Sense = 1…9) of the AC/DC Withstand

test.

Short:

This message appears on the display if the DUT current is well beyond the

metering range of the test.

Charge-LO:

This message appears on the display if the leakage current during

Ramp-up falls below the Charge -LO setting.

Breakdown:

This message appears on the display if the DUT current is well beyond

the metering range of the test and the arcing condition beyond the arc sense limit.

GND-Fault:

This message appears on the display if the GFI threshold is exceeded

during the test.

Interlock Open:

This message appears on the display if the Remote Interlock feature

is activated before or during a test.  The Remote Interlock feature utilizes a set of
closed contacts which will disable the instrument’s output if they are opened before or
during a test.  You can also refer to the Remote Interlock as a remote system lockout,
utilizing “fail when open” logic. You can disable the Remote Interlock feature by
plugging the “Interlock Disable Key” provided into the Signal Input connector.

Output Error:

This message appears on the display, if the instruments output reading

does not match the setting. You will only see this message if you press the EXIT key

«
...
127
128
129
130
131
...
»

Содержание HypotULTRA 7800















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HypotULTRA 7800

Бренд: C-LOGIC Страницы: 2

Бренд: Eaton Страницы: 53

Бренд: Oceanic Страницы: 75

TEC SourceMeter 2510

Бренд: Keithley Страницы: 244

Бренд: Kawai Страницы: 112

Бренд: QEED Страницы: 6

Бренд: Velleman Страницы: 107

Бренд: Emos Страницы: 76

Бренд: Hanna Instruments Страницы: 52

Recordall Series

Бренд: Badger Meter Страницы: 8

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренд: Caen Страницы: 50

Бренд: Reed Instruments Страницы: 14

iNELS Air AirCFS-100S

Бренд: Elko Страницы: 4

Бренд: PCE Health and Fitness Страницы: 7

EUROGRAND EG2080

Бренд: Behringer Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды