Arctic Cat WILDCAT/X Скачать руководство пользователя страница 96

Страница: 96 / 187

10. Making sure the tab on the throttle body aligns and

fully engages the alignment slot on the intake boot,

install the throttle body and tighten the clamp nut to

30 in.-lb; then install the engine ground cable.

WC164A

WC210A

11. Connect the ECT connector (A), front coil primary

connector (B), TPS connector (C), MAP/IAT connec-

tor (D), and ISC connector (E).

WC204A

WC206A

12. Install the fuel rail with fuel injectors and secure with

the cap screws. Tighten to 6 ft-lb.

13. Connect the gas line connectors to the fuel rails and

the electrical connectors to the fuel injectors.

WC203A

14. Place the inlet air duct into position; then install the

CVT intake cooling duct and secure with the clamp.

WC209A

15. Set the air filter housing into place and secure with the

three screws on the CVT housing and tighten to 6 ft-

lb; then connect and secure the throttle body inlet air

boot (A), crankcase breather hose (B), and inlet air

duct (C). Tighten the inlet air boot clamp to 30 in.-lb

and install the air filter housing strap.

WC146A

16. Install the CVT cooling outlet duct; then with a new gra-

foil gasket, install the rear exhaust pipe and cap screws

loosely.

17. Install the radiator/fan assembly and secure with the

mounting screws; then connect and secure the coolant

hoses with the clamps. Tighten securely.

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды