Arctic Cat WILDCAT/X Скачать руководство пользователя страница 83

Страница: 83 / 187

GZ299A

3. Remove the snap ring securing the water pump idler

shaft (C) in the crankcase; then remove the shaft and

bearings.

GZ463A

4. Remove the snap ring securing the oil pump driven

gear (D) to the oil pump driveshaft; then remove the

gear. Account for a drive pin and washer.

GZ463B

5. Remove the shift fork shaft (E); then remove the gear

shift shaft assembly (F). Account for a flat washer and

a spacer.

DE677A

GZ276

6. Remove two cap screws securing the oil pump in the

crankcase and remove the oil pump.

GZ305

7. Remove the driveshaft (G); then remove the counter-

shaft assembly (with shift forks) (H). Account for two

flat washers on the countershaft.

GZ280B

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды