Arctic Cat WILDCAT/X Скачать руководство пользователя страница 33

Страница: 33 / 187

2. To install a front seat, slide the front of the seat into

the seat retainers and push down firmly on the rear of

seat. The seat should automatically lock into position.

3. To remove a rear seat, remove two flange nuts secur-

ing the seat support to the floor; then remove the seat.

WC722A

4. To install a rear seat, place into position with the seat

support engaging the floor bolts; then install the

flange nuts and tighten securely.

Doors

CHECKING/ADJUSTING
(Wildcat/X)

The doors and latches are adjustable for proper latching/

unlatching.

1. To raise or lower door-to-latch contact or to move the

door forward or aft, loosen the screws on the hinge-

plate. After adjustment, tighten securely.

WC134A

WC109A

2. To move latch forward or aft, loosen the screws on the

latch plate. After adjustment, tighten securely.

WC133A

CHECKING/ADJUSTING
(Wildcat 4/4X)

To adjust the door latch anchors, loosen the two screws

and adjust the latch anchor for proper contact. When

latches are properly aligned, tighten securely.

WC133B

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды