Arctic Cat WILDCAT/X Скачать руководство пользователя страница 31

Страница: 31 / 187

WC348A

INSTALLING

1. Place the shift lever into position and secure with the

four machine screws (threads coated with blue Loctite

#243). Tighten to 20 ft-lb.

2. Connect the shift cable to the shift arm with the pivot

bolt and tighten the nut to 8 ft-lb.

3. Check shift cable adjustment (see Periodic Mainte-

nance/Tune-Up); then install the center console.

Tighten the machine screws securely.

4. Install the shift lever handle onto the shift lever and

tighten the jam nut with the handle correctly aligned.

5. Install the battery cover and seats.

Shift Cable

WC348B

WC178B

REMOVING

1. Remove the seats, battery cover, and center console.

2. Remove the nut (A) from the shift arm pivot bolt: then

loosen the jam nut (B) and lift the cable upward out of

the mounting bracket slot.

3. Remove the E-clip (C); then loosen jam nut (D) and

slide the cable (E) out of the mounting bracket.

4. From under the vehicle, mark any cable tie locations;

then remove the shift cable from the vehicle.

5. If the shift cable is to be replaced, accurately measure

and record the distance between the adjuster nuts (nuts

opposite the jam nuts).

INSTALLING

1. Using the measurements from the existing cable,

adjust the adjuster nuts to the same length.



NOTE: The shift cable will have to be adjusted, but

using the existing measurements will give a close
starting point.

2. From under the vehicle, thread the new cable into

position. Do not tie cable tie points yet.

3. Set the upper cable housing end into the mounting

bracket and finger tighten jam nut (B); then connect

the cable to the shift arm pivot bolt and secure with

the nut (A). Tighten the nut to 8 ft-lb.

4. Place the lower cable housing end into the mounting

bracket on the engine and finger tighten jam nut (D); then

connect cable (E) to the shift arm and install the E-clip (C).

5. Install any necessary cable ties as marked during

removal; then adjust the shift cable (see Periodic Main-

tenance/Tune-Up). After cable is properly adjusted,

tighten the jam nuts to 20 ft-lb.

6. Install the center console, battery cover, and seats.

LCD Gauge/Indicator

Lights/Dash Switches

REPLACING

1. Remove the hood and grille.

2. Remove the four screws securing the upper dash to the

frame.

WC329A

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды