Arctic Cat WILDCAT/X Скачать руководство пользователя страница 145

Страница: 145 / 187

143

WC282B

WC286A

7. Remove the rear axles from the rear drive gear case by

pushing the axle shaft toward the gear case and pull-

ing the CV/spline shaft out. Account for one O-ring on

each axle shaft.

PR729C

REMOVING FRONT DRIVE AXLE



NOTE: For removing a front drive axle, see Front

Differential in this section.

CLEANING AND INSPECTING

AXLES



NOTE: Always clean and inspect the drive axle com-

ponents to determine if any service or replacement is
necessary.

1. Using a clean towel, wipe away any oil or grease

from the axle components.

CD019

2. Inspect boots for any tears, cracks, or deterioration.



NOTE: If a boot is damaged in any way, it must be

replaced with a boot kit.

DISASSEMBLING AXLES



NOTE: Only the boots are serviceable on the axles;

if any other component is worn or damaged, the axle
must be replaced.

1. Using CV Boot Clamp Tool, remove and retain both

clamps for assembly purposes.

CF337

2. Place the white-striped end of the CV joint into a

vise.

CF335

3. To disengage the axle from the CV joint, sharply pull

back on the axle; then slide the boot off of the axle.

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды