Arctic Cat WILDCAT/X Скачать руководство пользователя страница 2

Страница: 2 / 187

FOREWORD

This Arctic Cat Service Manual contains service, maintenance, and troubleshooting information for certain 2014 Arctic

Cat Wildcat models (see cover). The complete manual is designed to aid service personnel in service-oriented applica-

tions.

This manual is divided into sections. Each section covers a specific vehicle component or system and, in addition to the

standard service procedures, includes disassembling, inspecting, and assembling instructions. When using this manual

as a guide, the technician should use discretion as to how much disassembly is needed to correct any given condition.

The service technician should become familiar with the operation and construction of each component or system by

carefully studying this manual. This manual will assist the service technician in becoming more aware of and efficient

with servicing procedures. Such efficiency not only helps build consumer confidence but also saves time and labor.

All Arctic Cat publications and decals display the words Warning, Caution, Note, and At This Point to emphasize

important information. The symbol

! WARNING

identifies personal safety-related information. Be sure to fol-

low the directive because it deals with the possibility of serious personal injury or even death. A

CAUTION

identi-

fies unsafe practices which may result in vehicle-related damage. Follow the directive because it deals with the

possibility of damaging part or parts of the vehicle. The symbol



NOTE:

identifies supplementary information wor-

thy of particular attention. The symbol



AT THIS POINT

directs the technician to certain and specific proce-

dures to promote efficiency and to improve clarity.

At the time of publication, all information, photographs, and illustrations were technically correct. Some photographs

used in this manual are used for clarity purposes only and are not designed to depict actual conditions. Because Arctic

Cat Inc. constantly refines and improves its products, no retroactive obligation is incurred.

All materials and specifications are subject to change without notice.

Keep this manual accessible in the shop area for reference.

Product Service and

Warranty Department

Arctic Cat Inc.

December 2013

®™ Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды