Arctic Cat WILDCAT/X Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 187

background image

60

GZ059

20. With the alignment pin installed in the rear camshaft,

loosely place the cam sprocket (with the recessed side

facing the cam shaft lobes) onto the camshaft. At this

point, do not “seat” the sprocket onto the shaft.

732-307B

GZ130



NOTE: At this point, oil the camshaft bearings, cam

lobes, and the three seating journals on the cylinder.

21. With the cam lobes directed down (toward the piston),

maneuver the camshaft/sprocket assembly through the

chain and towards its seating position; then loop the

chain over the sprocket.



NOTE: Note the position of the alignment marks on

the end of the camshaft. They should be parallel with
the plane of the cylinder head. If rotating the cam-
shaft is necessary for alignment, rotate the sprocket
inside the chain until the alignment pin can be
engaged in the sprocket with the camshaft in the
nearest possible position to parallel.

FW-014

GZ519

GZ518

22. Seat the cam sprocket onto the camshaft making sure

the alignment pin in the camshaft aligns with the

smallest hole in the sprocket; then place the camshaft/

sprocket assembly onto the cylinder ensuring the fol-

lowing.

GZ190B

A. Piston still at top-dead-center.

CORRECT

Wildcat/
Wildcat 4

X/4X

CORRECT

INCORRECT

«
...
60
61
62
63
64
...
»

Содержание WILDCAT/X




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WILDCAT/X

Бренд: Yutrax Страницы: 10

Бренд: MANCO Страницы: 4

Бренд: TransTank Страницы: 28

Бренд: ADLY MOTO Страницы: 42

Бренд: Yerf-Dog Страницы: 59

LEXION 770 2016

Бренд: Claas Страницы: 48

Бренд: Polaris Страницы: 146

Бренд: Craftsman Страницы: 56

Raider Max 175D

Бренд: Dazon Страницы: 43

Бренд: Daymak Страницы: 33

Sportsman 9920364

Бренд: Polaris Страницы: 143

Express L6 - Gas

Бренд: E-Z-GO Страницы: 80

MINI BAJA DUNE65

Бренд: Baja motorsports Страницы: 8

Бренд: Parklands Страницы: 66

Бренд: Samsung Страницы: 172

Бренд: Yamaha Страницы: 141

2009 Prowler XTZ

Бренд: Arctic Cat Страницы: 169

Бренд: Arctic Cat Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды