Arctic Cat WILDCAT/X Скачать руководство пользователя страница 115

Страница: 115 / 187

113

* After correcting condition, cycle key switch On-Off-On

Code

Fault Description

Fault Condition

Possible Cause

EPS Fault Recovery Method

C1301 Over Current

EPS internal over-current condition
has been detected

Internal EPS Condition

Correct EPS condition*

C1302 Excessive Current Error

EPS internal current measurement
error has been detected

Internal EPS Condition

Correct EPS condition*

C1303 Torque Sensor Range

Fault

EPS internal torque sensor range
condition has been detected

Internal EPS Condition

Correct EPS condition*

C1304 Torque Sensor Linearity

Fault

EPS internal torque sensor linearity
condition has been detected

Internal EPS Condition

Correct EPS condition*

C1305 Rotor Position Encoder

EPS internal rotor position encoder
condition has been detected

Internal EPS Condition

Correct EPS condition*

C1306 System Voltage Low

EPS battery power low-voltage condi-
tion has been detected

System voltage low (less than 11 VDC at
the EPS). Wire harness issue, faulty volt-
age regulator, weak battery or loose bat-
tery terminals.

EPS will auto-recover when the bat-
tery supply returns to normal

C1307 System Voltage High

EPS battery power over-voltage con-
dition has been detected

System voltage high (more than 16 VDC
at the EPS). Wire harness issue, faulty
voltage regulator or loose battery termi-
nals.

EPS will auto-recover when the bat-
tery supply returns to normal

C1308 Temperature Above 110°

EPS internal 110° C over-temp condi-
tion has been detected

Clean the EPS housing and cooling fins. EPS will auto-recover when internal

temperature drops below 105° C

C1309 Temperature Above 120°

EPS internal 120° C over-temp condi-
tion has been detected

Clean the EPS housing and cooling fins. EPS will auto-recover when internal

temperature drops below 115° C

C1310 Vehicle Speed High

Vehicle speed signal received by the
EPS exceeds the maximum speed
specification

Intermittent main harness wires, defective
speed-sensor, or intermittent speed sen-
sor wires.

EPS will auto-recover when the
vehicle speed signal drops below
the maximum speed specfication

C1311 Vehicle Speed Low

Vehicle speed signal received by the
EPS is zero or missing

Broken main harness wires, defective
speed-sensor, or broken speed sensor
wires.

EPS will auto-recover when the
vehicle speed signal returns to nor-
mal

C1312 Vehicle Speed Faulty

Vehicle speed CAN signal received by
the EPS incorrect or missing

Broken main harness CAN wires, defec-
tive speed-sensor, or broken speed sen-
sor wires.

EPS will auto-recover when the
vehicle speed signal returns to nor-
mal

C1313 Engine RPM High

Engine RPM signal received by the
EPS exceeds the maximum RPM
specification

Intermittent main harness RPM wires,
intermittent voltage regulator, intermittent
ACG stator wires.

EPS will auto-recover when engine
RPM signal drops below the maxi-
mum RPM specfication

C1314 Engine RPM Low

Engine RPM signal received by the
EPS suddenly dropped below 500
RPM

Handlebar switch in the "OFF" position,
broken main harness RPM wires, defect
voltage regulator, broken ACG stator
wires.

EPS will auto-recover when engine
RPM signal returns to normal

C1315 Engine RPM Faulty

Engine RPM CAN signal received by
the EPS incorrect or missing

Broken main harness CAN wires or
defective ECM.

EPS will auto-recover when engine
RPM signal returns to normal

C1316 EEPROM Error

EPS internal memory error has been
detected

Internal EPS condition

Correct EPS condition*

C1317 CAN Bus Error

The EPS has lost CAN communica-
tion with the EFI ECM

Broken CAN wires in the main harness.
EFI ECM connector has been discon-
nected.

Correct EPS condition*

C1318 Internal CRC Error

EPS internal CRC calculation condi-
tion has been detected

EPS reflash has failed. Battery power
was lost, or the keyswitch was turned off,
during EPS reflash programming.

EPS must be reprogrammed

C1319 Boot Counter Exceeded

EPS internal application code condi-
tion has been detected

Intermittent power has prevented a suc-
cessful application code launch.

Correct EPS power condition*

C1320 Incorrect Vehicle Speed-

to-RPM Ratio

Vehicle speed signal received by the
EPS exceeds 10 MPH, but the engine
RPM signal less than 500 RPM

Intermittent or broken main harness RPM
wires, intermittent voltage regulator, inter-
mittent or broken ACG stator wires.

Correct EPS condition*

C1321 Vehicle Speed Erratic

Vehicle speed signal received by the
EPS changing at an unrealistic rate

Intermittent main harness, intermittent
speed sensor, dirty speed senor or trigger
wheel.

Correct EPS vehicle speed signal
condition*

C1322 Engine RPM Lost

Engine RPM signal received by the
EPS exceeds 500 RPM and then is
zero or missing

Handlebar switch in the "OFF" position,
broken main harness RPM wires, defect
voltage regulator, broken ACG stator
wires.

EPS will auto-recover when engine
RPM signal returns to normal

C1323 "EPS OFF" Gauge Dis-

play

Battery power has been applied to the
EPS for more than 5-minutes, but no
engine RPM signal has been
detected

The EPS has been automatically dis-
abled, after 5-minutes of inactivity, to con-
serve battery power.

EPS will auto-recover when engine
is started or the keyswitch is cycled
On-Off-On

C1324 Loss of CAN communica-

tion with EPS unit

The gauge has lost CAN communica-
tion with the EPS

Broken CAN wires in the main harness or
disconnected EPS. This is not an EPS
generated DTC; gauge DTC display only.

Gauge DTC display will clear when
the EPS-to-gauge CAN communica-
tion is restored.

C1325 Dual Loss

EPS loss of both the vehicle speed
and the engine RPM signals has been
detected

Handlebar switch in the "OFF" position,
the engine stalled (keyswitch "ON"), bro-
ken harness wires, loss of CAN data sig-
nal.

EPS will auto-recover when either
the vehicle speed or engine RPM
signal is restored.

C1326 Rotor Position Encoder

EPS internal rotor position encoder
variance condition has been detected

Internal EPS Condition

Correct EPS condition*

C1327 Voltage Converter Error

(Low)

EPS internal voltage converter low-
voltage condition has been detected

Internal EPS Condition

Correct EPS condition*

C1328 Voltage Converter Error

(High)

EPS internal voltage converter over-
voltage condition has been detected

Internal EPS Condition

Correct EPS condition*

C1329 Internal Data Error

EPS internal preloaded data condition
has been detected

Internal EPS Condition

EPS must be reprogrammed

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды