Arctic Cat WILDCAT/X Скачать руководство пользователя страница 59

Страница: 59 / 187

GZ159

3. Lubricate the inside wall of the cylinder; then using a

ring compressor, compress the rings and slide the cyl-

inder over the piston. Route the cam chain up through

the cylinder cam chain housing; then remove the pis-

ton holder and seat the cylinder firmly on the crank-

case.

GZ142

4. Loosely install the two nuts securing the cylinder to

the crankcase.



NOTE: The two cylinder-to-crankcase nuts will be

tightened in step 10.

GZ141A

GZ160A

5. Install the coolant hose onto the crankcase union and

tighten the clamp.

C. Cylinder Head
D. Valve Cover



NOTE: Steps 1-5 in the preceding sub-section must

precede this procedure.

6. Place the chain guide into the cylinder.

GZ161A

7. Place a new head gasket into position on the cylinder.

Place the alignment pins into position; then place the

head assembly into position on the cylinder while

guiding the cam chain through the cylinder head.

GZ151

8. Install the cylinder head cap screws. Tighten only

until snug.

CAUTION

The cylinder should slide on easily. Do not force the cyl-
inder or damage to the piston, rings, cylinder, or crank-
shaft assembly may occur.

CAUTION

Care should be taken that the bottom of the chain guide
is secured in the crankcase boss.

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды