Arctic Cat WILDCAT/X Скачать руководство пользователя страница 63

Страница: 63 / 187

B. Camshaft lobes directed down (toward the piston).

C. Camshaft alignment marks parallel to the valve

cover mating surface.

D. Recessed side of the sprocket directed toward the

cam lobes.

E. Camshaft alignment pin and sprocket alignment

hole (smallest) are aligned.

23. Place tab-washer onto the sprocket making sure it

covers the pin in the alignment hole.

ATV-1027

24. Install the first cap screw (threads coated with red

Loctite #271) securing the sprocket and tab-washer to

the camshaft. Tighten only until snug.

GZ195

25. Rotate the crankshaft until the second cap screw

securing the sprocket to the camshaft can be installed;

then install the cap screw (threads coated with red

Loctite #271) and tighten to 11 ft-lb. Bend the tab to

secure the cap screw.

GZ193

CD465

26. Rotate the crankshaft until the first cap screw (from

step 23) can be addressed; then tighten to 11 ft-lb.

Bend the tab to secure the cap screw.

GZ194

27. Place the C-rings into position in their grooves in the

cylinder heads.

CC012D

CAUTION

If any of the above factors are not as stated go back to
step 19 and carefully proceed.

CAUTION

Care must be taken that the tab-washer is installed cor-
rectly to cover the alignment hole on the sprocket. If the
alignment pin falls out, severe engine damage will
result.

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды