Arctic Cat WILDCAT/X Скачать руководство пользователя страница 21

Страница: 21 / 187

WC346A

WC347A

2. Remove the hose clamp from the gasoline filler neck

and disconnect the filler hose.

WC344A

3. Lift the rear body panel off and remove forward

between the ROPS uprights; then tape or plug the filler

hose to prevent contamination of fuel or vapor escaping.

WC186

INSTALLING

1. Place the rear body panel onto the vehicle making sure

the outer front mounting tabs are located behind the

splash panel.

WC342A

2. Secure with the machine screws and tighten securely.

3. Remove the plug or tape from the gas filler hose and

connect the hose to the gasoline filler neck and secure

with the hose clamp. Tighten securely.

Electronic Power

Steering (EPS)



NOTE: Thoroughly troubleshoot the EPS system

prior to replacing the EPS assembly (see Electrical
System) as there are several possible external
causes for system failure.

REMOVING



NOTE: Before removing the EPS, ensure the front

wheels and steering wheel are aligned to the front.

1. Remove two cap screws and two fender screws secur-

ing the grille and remove the grille.

WC081C

2. Remove two fender screws behind the headlights and

two fender screws at the rear of the hood; then remove

the hood.

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды