Arctic Cat WILDCAT/X Скачать руководство пользователя страница 149

Страница: 149 / 187

147

WC169A

WC170C

8. Remove the lower front through-bolt; then remove the

boot clamp on the input drive coupler and slide the

gear case to the rear until drive coupler disengages.

WC288A

WC743

9. Lay the gear case on its left side and remove from

either side of the vehicle. Account for the spring and

washer with the drive coupler.

WC290

RING GEAR/THRUST BUTTON
Removing

1. Remove the cap screws securing the gear case cover

to the gear case; then remove the ring gear.

2. Remove the thrust button from the gear case cover

(left-hand threads). Account for a shim.

Inspecting

1. Inspect the ring gear for excessive wear, missing or

chipped teeth, or discoloration.

2. Inspect the thrust button for excessive wear or discol-

oration.

3. Inspect the bearings for discoloration, roughness, or

excessive wear.



NOTE: For servicing bearings or seals, see Front

Differential in this section.

Installing/Shimming



NOTE: Ring gear clearance must be adjusted prior

to selecting shim for the thrust button.

1. Install the thrust button with shim into the gear case

cover and tighten securely (left-hand threads).



AT THIS POINT

On the Wildcat 4/4X if the technician’s objective is to
remove the rear driveshaft, release the clamp secur-
ing the shaft to the gear case; then slide the shaft
from the gear case.

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды