Arctic Cat WILDCAT/X Скачать руководство пользователя страница 85

Страница: 85 / 187



NOTE: Do not use a new lock nut at this time as this

procedure may have to be repeated.

5. Place the assembled shaft into the left crankshaft case;

then lightly coat the gear teeth with machinist’s lay-

out dye. Rotate the shafts through several rotations in

both directions. Gear contact should extend from the

root to the top of the gear teeth.

MT016A

6. To adjust tooth contact, use the following chart to cor-

rectly shim the driven shaft.

7. After correct tooth contact is established, proceed to

Checking Backlash in this sub-section.

Checking Backlash

1. Install the drive bevel gear assembly and driven bevel

gear/output shaft assembly into the crankcase bottom

cover.

2. Mount the dial indicator so the tip is contacting a tooth

on the secondary drive bevel gear.

FW-008

3. Firmly hold the bearing down and while rocking the

drive bevel gear back and forth, note the maximum

backlash reading on the gauge.

GZ398

4. Acceptable backlash range is 0.127-0.381 mm (0.005-

0.015 in.).

Correcting Backlash



NOTE: If backlash measurement is within the

acceptable range, no correction is necessary.

1. If backlash measurement is less than specified,

remove an existing shim, measure it, and install a new

thinner shim.

FW-006A

2. If backlash measurement is more than specified,

remove an existing shim, measure it, and install a

thicker shim.



NOTE: Continue to remove, measure, and install

until backlash measurement is within tolerance. Note
the following chart.

3. Once correct gear pattern and backlash are established,

install a new output pinion nut (coated with red Loctite

#263) on the output shaft and tighten to 200 ft-lb.

4. Using an appropriate holding fixture and wrench

adapter, install the secondary drive gear nut (threads

coated with red Loctite #263) and tighten to 200 ft-lb.

The output drive assembly is now ready for installa-

tion.

Tooth Contact

Shim Correction

Contact at Top

Increase Shim Thickness

Contact at Root

Decrease Shim Thickness

Backlash Measurement

Shim Correction

Under 0.127 mm (0.005 in.)

Decrease Shim Thickness

At 0.127-0.381 mm (0.005-0.015 in.)

No Correction Required

Over 0.381 mm (0.015 in.)

Increase Shim Thickness

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды