Arctic Cat WILDCAT/X Скачать руководство пользователя страница 26

Страница: 26 / 187

Steering Shaft

REMOVING

1. Remove the steering wheel.

2. Remove the hood and grille.

3. Remove the upper pivot bolt on the steering tilt link

and drop the tilt link down clear of the dash.

WC330

4. Remove four upper dash mounting screws and block

the dash to the rear.

WC329A

5. Remove the steering shaft housing support hold-down

strap; then remove the U-clamp from the lower steer-

ing shaft support.

WC247A

WC328A

6. Remove the steering shaft from the EPS by pulling

straight away from the input shaft.

WC335

7. Remove the upper and lower snap rings from steering

shaft; then work the steering shaft out of the upper

steering support housing and remove from the vehicle.

Account for a flat washer and a wave washer.

WC326

WC337A

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды