Arctic Cat WILDCAT/X Скачать руководство пользователя страница 79

Страница: 79 / 187

GZ442

2. Remove the snap ring securing the bearing in the

water pump drive cover; then remove the bearing

using an appropriate blind bearing remover.

GZ441

Inspecting

1. Inspect the water pump drive housing (A) for scoring

or discoloration.

GZ440A

2. Inspect the bearing (B) for smooth rotation and no dis-

coloration or scoring.

3. Inspect the gear (C) for chipped or missing teeth,

excessive hub wear, or excessive wear in the drive pin

slot.

4. Inspect the drive pin (D) and driveshaft (E) for exces-

sive wear or looseness.

Assembling

1. Install the bearing in the water pump drive cover and

secure with the snap ring (flat side away from the

bearing).

GZ441

2. Install the gear onto the driveshaft noting correct ori-

entation (from step 1 of disassembling).

GZ442

3. Install the two snap rings on the driveshaft (flat side

away from the gear).

Installing Right-Side

Components

1. Place a new clutch housing seal (spring side facing

Clutch Housing Seal Tool) into the clutch cover and

secure with a rubber mallet or press.

GZ530

2. Using a suitable press, install the bearing into the

clutch cover against the outer bearing face.

Содержание WILDCAT/X




























































































































































































Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды

Arctic Cat WILDCAT/X, Руководство по обслуживанию

Результаты поиска

Содержание WILDCAT/X

Отзывы:

Похожие инструкции для WILDCAT/X

Бренды по названию

Популярные бренды