Arctic Cat WILDCAT/X Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 187

background image

70

GZ225

13. Install the starter driven and counter gear shafts (D)

into the crankcase (longer shaft to the front); then

install the starter countershaft gear (C), starter driven

gear (A), and bushing (B) making sure the chamfered

gear teeth on the countershaft gear are directed out-

ward.

GZ224A

14. Install the starter motor with a new O-ring lightly

lubricated with grease; then tighten the mounting cap

screws to 8 ft-lb.

GZ251

15. Using Seal Protector Tool, install the outer magneto

cover using a new gasket and secure with the cap

screws. Using the pattern shown, tighten to 112 in.-lb.

GZ212B

Right-Side Components



NOTE: For efficiency, it is preferable to remove and

disassemble only those components which need to be
addressed and to service only those components. The
technician should use discretion and sound judgment.



NOTE: The engine/transmission does not have to

be removed from the frame for this procedure.

Removing Right-Side

Components

A. CVT Cover
B. Drive Clutch
C. Driven Clutch
D. Inner Clutch Cover

1. Remove the cap screws securing the CVT cover; then using

a rubber mallet, gently tap on the cover tabs to loosen the

cover. Account for a gasket and two alignment pins.

2. Remove the cap screw securing the driven clutch; then

remove the outer sheave of the driven clutch. Account

for a flat washer and alignment shim(s).

WC809

CAUTION

Make sure the one-way starter clutch is properly
engaged with the starter ring gear before installing and
tightening the rotor/flywheel nut or damage to the
clutch assembly could occur.



AT THIS POINT

To service any one specific component, only limited dis-
assembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

«
...
70
71
72
73
74
...
»

Содержание WILDCAT/X




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WILDCAT/X

Бренд: KAYO MOTOR Страницы: 90

1997 TRX300 Fourtrax 300

Бренд: Honda Страницы: 162

Бренд: UtilityDump Страницы: 13

Бренд: Taylor-Dunn Страницы: 132

Бренд: Yamaha Страницы: 46

Бренд: Yamaha Страницы: 155

Бренд: Yamaha Страницы: 190

Бренд: Arrowquip Страницы: 16

Outlander 400 EFI 2009

Бренд: Can-Am Страницы: 160

Бренд: Ezytrail Страницы: 28

Бренд: Alpine Страницы: 42

Бренд: Kubota Страницы: 112

Бренд: Ifor Williams Trailers Страницы: 55

Бренд: Yamaha Страницы: 122

Бренд: GAS GAS Страницы: 60

Бренд: Power Fist Страницы: 8

CF MOTO CFORCE 625

Бренд: DFK Страницы: 64

Бренд: Yamaha Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды