ARAG BRAVO 300S, Инструкция по установке, эксплуатации и обслуживанию

Страница: 47 / 52

47
MAINTENANCE / DIAGNOSTICS / REPAIRS
14.2 Troubleshooting
fauLt cause remedy
The display does not switch on
No power supply • Check power supply connection (Par. 7.2).
Computer is OFF • Press the ON key.
Valve controls take no effect Valves not connected • Connect the connectors (Par. 8.3).
One valve does not open No power supply to valve • Check valve electric connection and operation.
The display no longer shows the speed
Wrong setup • Check the setup of the wheel constant (Par. 11.1).
No signal coming from the speed sensor • Check connections to speed sensor (Par. 8.5).
The displayed speed is not precise Wrong setup • Check the setup of the wheel constant (Par. 11.1).
Output volume readout inaccurate Wrong setup
• Check the coverage setup and the row width (Par. 10.4 - 11.2).
• Check the setup of the flowmeter constant (Par. 10.5).
• Check the setup of the wheel constant
(Par. 11.1).
• Check the setup of the section valve type (Par. 10.8).
• Check connections to speed sensor
(Par. 8.5).
Sprayed surface count displayed does not
match actual sprayed surface
Wrong setup
• Check the coverage setup and the row width
(Par. 10.4 - 11.2).
• Check the setup of the wheel constant (Par. 11.1).
• Check connections to speed sensor (Par. 8.5).
Distance traveled count displayed does not
match actual distance covered
Wrong setup
• Check the setup of the wheel constant (Par. 11.1).
• Check connections to speed sensor
(Par. 8.5).
Sprayed fluid count displayed does not match
litres/gpm actually sprayed
Wrong setup
• Check the setup of the flowmeter constant
(Par. 10.5).
• Check the setup of the section valve type (Par. 10.8).
Use of three-way section valves without setting
calibrated backflows
• Perform setting.
Unable to reach output volume value set for the
automatic operation
Wrong setup
• Check spray rate setup (Par. 11.2).
• Check the coverage setup and the row width
(Par. 10.4 - 11.2).
System not adequately sized to provide required rate
• Check maximum pressure valve setting.
• Make sure control valve is adequate for specific system.
Control valve malfunction • Check valve operation.
Instantaneous pressure readout inaccurate
Wrong setup • Check full scale setup for pressure sensor (Par. 10.6).
Pressure sensor not calibrated • Perform the calibration (Par. 12.3).
Pressure sensor wrong installation • Check connections to pressure sensor (Par. 8.5).
Instantaneous pressure is not displayed
Wrong setup • Check pressure sensor setting (Par. 10.6).
Computer does not receive signals from pressure
sensor
• Check connections to pressure sensor
(Par. 8.5).
Pressure sensor wrong installation • Check connections to pressure sensor (Par. 8.5).
Rpm readout inaccurate Wrong setup • Check rpm sensor constant setting (Par. 10.10).
Rpm value not displayed
Computer does not receive signals from RPM
sensor
• Check connections to RPM sensor
(Par. 8.5).
Rpm sensor wrong installation • Check connections to RPM sensor (Par. 8.5).
The displayed tank level is not precise
Level sensor not calibrated
• Perform the calibration (Par. 10.9.3).
• Calibrate the level sensor again
(Par. 10.9.3).
Level sensor wrong installation • Check connections to level sensor
(Par. 8.5).
Pump failure alarm permanently active
Computer does not receive signals from Pump
Protector sensor
• Check connections to Pump Protector sensor (Par. 8.5).
During the tank calibration procedure, the
sprayed quantity is always steady on zero
Wrong installation / no flowmeter installed
• Check connections to flowmeter (Par. 8.5).
• Install the flowmeter (Par. 6.1).
Section valves and main control valve set to OFF • Take section valves and main control valve to ON (Par. 10.9.3).
14.3 Cleaning rules
- Clean only with a soft wet cloth.
- DO NOT use aggressive detergents or products.
- DO NOT clean equipment with direct water jets.
Fig. 123