Analog Devices ADuCM310 Скачать руководство пользователя страница 154

Страница: 154 / 192

UG-549

ADuCM310 Hardware Reference Manual

Rev. C | Page 154 of 192

Bits

Bit Name

Description

Reset

Access

Stick parity. Forces parity to defined values. When set, the parity is based
on the following bit settings:

0x0

EPS = 1 and PEN = 1, parity is forced to 0.

EPS = 0 and PEN = 1, parity is forced to 1.

EPS = X and PEN = 0, no parity is transmitted.

0: parity is not forced based on EPS and PEN.

1: parity forced based on EPS and PEN.

EPS

Parity select. This bit only has meaning if parity is enabled (PEN set).

0x0

0: odd parity is transmitted and checked.

1: even parity is transmitted and checked.

PEN

Parity enable. Controls the parity bit transmitted and checked. The value
transmitted and the value checked are based on the settings of EPS and SP.

0x0

0: parity is not transmitted or checked.

1: parity is transmitted and checked.

STOP

Stop bit. Controls the number of stop bits transmitted. In all cases, only the
first stop bit is evaluated on data received.

0x0

0: send 1 stop bit regardless of the word length (WLS).

1: send a number of stop bits based on the word length. Transmit 1.5 stop

bits if the word length is 5 bits (WLS = 00), or 2 stop bits if the word length
is 6 (WLS = 01), 7 (WLS = 10), or 8 bits (WLS = 11).

[1:0]

WLS

Word length select. Selects the number of bits per transmission.

0x0

00: 5 bits.

01: 6 bits.

10: 7 bits.

11: 8 bits.

Modem Control Register

Address: 0x40005010, Reset: 0x0000, Name: COMMCR

Table 219. Bit Descriptions for COMMCR

Bits

Bit Name

Description

Reset

Access

[15:5]

RESERVED

Reserved.

0x0

LOOPBACK

Loopback mode. In loopback mode, SOUT is forced high. The modem

signals are also directly connected to the status inputs (RTS to CTS, DTR to
DSR, OUT1 to RI, and OUT2 to DCD).

0x0

0: normal operation; loopback disabled.

1: loopback enabled.

OUT2

Output 2.

0x0

0: force OUT2 to a Logic 1.

1: force OUT2 to a Logic 0.

OUT1

Output 1.

0x0

0: force OUT1 to a Logic 1.

1: force OUT1 to a Logic 0.

RTS

Request to send.

0x0

0: force RTS to a Logic 1.

1: force RTS to a Logic 0.

DTR

Data terminal ready.

0x0

0: force DTR to a Logic 1.

1: force DTR to a Logic 0.

Содержание ADuCM310

































































































































































































Результаты поиска

Содержание ADuCM310

Отзывы:

Похожие инструкции для ADuCM310

Бренды по названию

Популярные бренды

Analog Devices ADuCM310, Справочник по аппаратуре

Результаты поиска

Содержание ADuCM310

Отзывы:

Похожие инструкции для ADuCM310

Бренды по названию

Популярные бренды