Analog Devices ADuCM310 Скачать руководство пользователя страница 143

Страница: 143 / 192

ADuCM310 Hardware Reference Manual

UG-549

Rev. C | Page 143 of 192

Bits

Bit Name

Description

Reset

Access

TIM

SPI transfer and interrupt mode.

0x0

0: cleared by user to initiate transfer with a read of the SPI0RX register.
Interrupt only occurs when Rx is full.

1: set by user to initiate transfer with a write to the SPI0TX register.
Interrupt only occurs when Tx is empty.

LSB

LSB first transfer enable.

0x0

0: MSB transmitted first.

1: LSB transmitted first.

WOM

SPI wired-OR mode.

0x0

1: open circuit data output enable. External pull-ups required on data out pins.

0: normal output levels.

CPOL

Serial clock polarity.

0x0

0: serial clock idles low.

1: serial clock idles high.

CPHA

Serial clock phase mode.

0x0

1: serial clock pulses at the beginning of each serial bit transfer.

0: serial clock pulses at the end of each serial bit transfer.

MASEN

Master mode enable.

0x0

0: enable slave mode.

1: enable master mode.

ENABLE

SPI enable.

0x0

0: disable the SPI.

1: enable the SPI.

SPI DMA Enable Register

Address: 0x4002C014, Reset: 0x0000, Name: SPI0DMA

Table 203. Bit Descriptions for SPI0DMA

Bits

Bit Name

Description

Reset

Access

[15:3]

RESERVED

Reserved.

0x0

IENRXDMA

Enable receive DMA request.

0x0

0: disable Rx DMA interrupt.

1: enable Rx DMA interrupt.

IENTXDMA

Enable transmit DMA request.

0x0

0: disable Tx DMA interrupt.

1: enable Tx DMA interrupt.

ENABLE

Enable DMA for data transfer. Set by user code to start a DMA transfer.

Cleared by user code at the end of DMA transfer. This bit must be cleared
to prevent extra DMA requests to the µDMA controller.

0x0

Transfer Byte Count Register

Address: 0x4002C018, Reset: 0x0000, Name: SPI0CNT

Table 204. Bit Descriptions for SPI0CNT

Bits

Bit Name

Description

Reset

Access

[15:8]

RESERVED

Reserved.

0x0

[7:0]

COUNT

Transfer byte count. COUNT indicates the number of bytes to be transferred.

COUNT is used in both receive and transmit transfer types. The COUNT value
assures that a master mode transfer terminates at the proper time and that

16-bit DMA transfers are byte padded or discarded as required to match
odd transfer counts. Reset by clearing SPI0CON[0] or if SPI0CNT is updated.

0x0

Содержание ADuCM310

































































































































































































Результаты поиска

Содержание ADuCM310

Отзывы:

Похожие инструкции для ADuCM310

Бренды по названию

Популярные бренды

Analog Devices ADuCM310, Справочник по аппаратуре

Результаты поиска

Содержание ADuCM310

Отзывы:

Похожие инструкции для ADuCM310

Бренды по названию

Популярные бренды