Allied Telesis AT-FAN08 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 214

background image

Chapter 7: Cabling the AT-XEM2 Line Card Ports

160

Installing and Cabling Fiber Optic Transceivers

Table 15 lists the types of fiber optic transceivers that are supported by the
AT-XEM2 line cards. Refer to the product datasheet for a list of approved
transceivers.

Please review “Guidelines to Handling Twisted Pair or Fiber Optic
Transceivers” on page 159 before performing the procedure.

Your transceivers may look different than those shown in the following
illustrations.

Warning

The temperature of an operational transceiver can exceed 70° C
(158° F). Exercise caution when removing or handling transceivers
with unprotected hands.



E43

To install a fiber optic transceiver in an Ethernet line card, perform the
following procedure:

1. Select a slot in the AT-XEM2 line card for the transceiver.

2. If the selected slot has a dust cover, remove it.

3. Remove the transceiver from its shipping container and store the

packaging material in a safe location.

4. Orient the transceiver and slide it into the slot until it clicks into place.

The correct orientation depends on the line card and transceiver:



AT-XEM2-12XS Line Card - To install a transceiver in an odd
numbered slot, position its handle on the right. To install a
transceiver in an even numbered slot, position its handle on the
left. Refer to Figure 100 on page 161.

Table 15. AT-XEM2 Line Cards and Fiber Optic Transceivers

Ethernet Line Card

Fiber Optic Transceiver

AT-XEM2-12XS

1Gbps SX or LX SFP

10Gbps SR or LR SFP

AT-XEM2-4QS

40Gbps QSFP+

AT-XEM2-1CQ

100Gbps SR or LR QSFP28

«
...
158
159
160
161
162
...
»

Содержание AT-FAN08























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-FAN08

BNI IOL-727-S51-P012

Бренд: Balluff Страницы: 20

MSD-804FD Series

Бренд: IDK Страницы: 133

Бренд: IDK Страницы: 150

Бренд: IDK Страницы: 101

Бренд: IDK Страницы: 85

Бренд: IDK Страницы: 40

Бренд: IDK Страницы: 97

Бренд: IDK Страницы: 117

Бренд: IDK Страницы: 77

Бренд: H3C Страницы: 90

Бренд: Yamamoto Electric Works Co., Ltd. Страницы: 15

Бренд: Black Box Страницы: 4

Бренд: Crestron Страницы: 2

Premasreg 716 Series

Бренд: S+S Regeltechnik Страницы: 32

LVP-51 LVP-51 Series

Бренд: Omega Engineering Страницы: 6

tecatlantis EASY LED CONTROL 2 PLUS

Бренд: Aquatlantis Страницы: 4

Бренд: Milestone pro Страницы: 32

Бренд: Black Box Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды