Allied Telesis AT-FAN08 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 214

background image

AT-SBx908 GEN2 Installation Guide for Virtual Chassis Stacking

159

Guidelines to Handling Twisted Pair or Fiber Optic Transceivers

Please review the following guidelines before installing twisted pair or fiber
optic transceivers in AT-XEM2 line cards:



Transceivers are hot-swappable. You can install them while the
switch is powered on.



For a list of supported transceivers, refer to the product data sheet
on the Allied Telesis web site.



The operational specifications and fiber optic cable requirements
are provided in the documents included with the transceivers.



You should install transceivers in AT-XEM2 line cards before
connecting their fiber optic cables.



Fiber optic transceivers are dust sensitive. Always keep the plug in
the optical bores when a fiber optic cable is not installed, or when
you store the transceiver. When you do remove the plug, keep it for
future use.



Repetitive removal or insertion of a transceiver can lead to
premature failure.



100Gbps transceivers for the AT-XEM2-1CQ line card have
handles. Use the handles when installing or removing transceivers.
An example is shown in Figure 99.

Figure 99. Handle on 100Gbps Transceivers for the AT-XEM2-1CQ Line

Card

Caution

Transceivers can be damaged by static electricity. Be sure to
observe all standard electrostatic discharge (ESD) precautions,
such as wearing an antistatic wrist strap, to avoid damaging the
devices.



E92

Handle

«
...
157
158
159
160
161
...
»

Содержание AT-FAN08























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-FAN08

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 1

Cleveland Controls RSS-498-013

Бренд: UNICONTROL Electronic Страницы: 2

Бренд: PRO SIGNAL Страницы: 5

Edge RTM-ATCA-F140

Бренд: Penguin Страницы: 2

Бренд: König Страницы: 8

EXHL-TRN-LE1 Series

Бренд: Larson Electronics Страницы: 2

SISTG1040-242-LRT

Бренд: Transition Networks Страницы: 31

Бренд: TAXON TOOLS Страницы: 9

Бренд: DirectConnect Страницы: 10

Бренд: Phonocar Страницы: 2

Бренд: Abseco Страницы: 10

Бренд: Black Box Страницы: 74

Бренд: Minicom Страницы: 16

Бренд: Pilz Страницы: 20

EdgeSwitch 8 150W

Бренд: Ubiquiti Страницы: 28

Бренд: Madison Страницы: 2

Бренд: H3C Страницы: 96

Бренд: NVision Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды