Allied Telesis AT-FAN08 Скачать руководство пользователя страница 198

Страница: 198 / 214

Chapter 9: Replacing Modules

198

Figure 129. Disconnecting the AT-FAN08 Module from the Chassis

3. Continue with the next procedure to install a new AT-FAN08 Module.

Installing AT-

FAN08 Modules

This procedure requires the following tool:



#2 Phillips-head screwdriver (not provided)

The illustrations show the installation of the fan module in Fan A slot on
the back panel. The procedure is the same for installing the module in the
Fan B slot.

To install an AT-FAN08 Module, perform the following procedure:

1. Align the AT-FAN08 Module in the slot as shown in Figure 130 on

page 199.

Содержание AT-FAN08























































































































































































































Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды

Allied Telesis AT-FAN08, Руководство по установке

Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды