Allied Telesis AT-FAN08 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 214

background image

Chapter 5: Powering On the Chassis

110

Powering On AT-SBxPWRSYS1-80 DC Power Supplies

The procedure in this section explains how to power on AT-
SBxPWRSYS1-80 DC Power Supplies. If you have not installed the power
supplies, refer to “Installing AT-SBxPWRSYS1-80 DC Power Supplies” on
page 91 for instructions.

Before powering on the chassis, review the information in “Power
Specifications” on page 209 for the power specifications of the switches.

The power supply unit has a ground connection and positive and negative
DC terminals. You may install the ground and power lead wires with the
terminal lugs that come with the unit or with bare wire. The wire
requirements are slightly different for terminal installation versus bare wire
installation. Here are the wire requirements if you are using the terminals
that come with the power supply:



Two 8 AWG stranded power wires (not provided)



One 10 AWG stranded grounding wire (not provided)

Here are the wire requirements for bare wire installation:



Two 8 AWG solid or stranded power wires (not provided)



One 10 AWG solid or stranded grounding wire (not provided)

Here is a list of the required tools:



Crimping tool (not provided)



8 mm wrench (not provided)



#1, #2, and #3 Phillips-head screwdrivers (not provided)



#3 Phillips-head 30 to 40 inch-lbs Phillips-head torque screwdriver
(optional - not provided)

Here are the procedures for powering on AT-SBxPWRSYS1-80 DC Power
Supplies:



“Choosing a Method for Attaching the Grounding Wire” on page 112



“Connecting the Grounding Wire with the Grounding Terminal” on
page 112



“Connecting the Grounding Wire with Bare Wire” on page 117



“Choosing a Method for Attaching the Power Wires” on page 119



“Connecting the DC Power Wires with the Straight Terminals” on
page 119



“Connecting the DC Power Wires with the Right Angle Terminals” on
page 127

«
...
108
109
110
111
112
...
»

Содержание AT-FAN08























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-FAN08

Бренд: DAB Страницы: 56

Бренд: Sarowin Страницы: 9

Бренд: AsGa Страницы: 23

Бренд: Extron electronics Страницы: 137

24-Port Gigabit Switch

Бренд: Belkin Страницы: 2

852-1411/000-001

Бренд: WAGO Страницы: 40

Бренд: Manhattan Страницы: 4

AV Selector 310

Бренд: Hama Страницы: 21

Бренд: Scame electrical solutions Страницы: 68

EdgeSwitch 8 150W

Бренд: Ubiquiti Страницы: 28

Бренд: Leaksafe Solutions Страницы: 12

Бренд: H3C Страницы: 3

Бренд: Omega Engineering Страницы: 16

Giga-AcessEtherLinx-II

Бренд: IMC Networks Страницы: 40

Бренд: ATEN Страницы: 15

Бренд: Tripp Lite Страницы: 9

ePowerSwitch 8XM Master

Бренд: ADDER Страницы: 2

Lanolinx LNX-1002GN

Бренд: ANTAIRA Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды