Allied Telesis AT-FAN08 Скачать руководство пользователя страница 143

Страница: 143 / 214

AT-SBx908 GEN2 Installation Guide for Virtual Chassis Stacking

143

Write down the feature
licenses.

“Viewing Optional Feature
Licenses” on page 150

SHOW LICENSE BRIEF
command in User Exec or
Privileged Exec mode.

Enable the VCStack
feature.

“Enabling the VCStack
Feature” on page 151

STACK ENABLE
command in the Global
Configuration mode.

Save your changes

WRITE command in the
Privileged Exec mode.

Reboot the switch.

REBOOT command in the
Privileged Exec mode.

Wait three minutes for the
switch to initialize its
operating software.

Start a new local
management session.

“Starting a Local
Management Session” on
page 145

Designate the trunk ports
for the switch.

“Designating Trunk Ports”
on page 153

STACKPORT command
in port Interface modes.

Save your changes

WRITE command in the
Privileged Exec mode.

Power off the switch.

“Powering Off the Switch”
on page 156

Repeat steps 1 to 12 on
each switch.

Compare the version
numbers of the
AlliedWare Plus operating
software on the switches.
If necessary, upgrade the
switches so that they all
have the same version.

Software Reference for
SBx908 GEN2 Series
Switches, AlliedWare
Plus Operating System

Compare the optional
feature licenses. If
necessary, add or remove
licenses so that they all
have the same licenses.

Software Reference for
SBx908 GEN2 Series
Switches, AlliedWare
Plus Operating System

Table 12. Switch Configuration Procedures (Continued)

Step

Description

Procedure

AlliedWare Plus

Command or Manual

Содержание AT-FAN08























































































































































































































Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды

Allied Telesis AT-FAN08, Руководство по установке

Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды