Allied Telesis AT-FAN08 Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 214

background image

201

Chapter 10

Troubleshooting

This chapter contains suggestions on how to troubleshoot problems with
the switch.

Note

For further assistance, please contact Allied Telesis Technical
Support at

www.alliedtelesis.com/support

.

Problem 1:

All the port LEDs and Switch ID LED are off, and the fans are

not operating.

Solutions:

The unit is not receiving power. If the switch has AT-

SBxPWRSYS2 AC Power Supplies, try the following:



Verify that the power cord is securely connected to the power
source and the AC connector on the back panel of the switch.



Verify that the power outlet has power by connecting another
device to it.



Try connecting the unit to another power source.



Try a different power cord.



Verify that the voltage from the power source is within the required
levels for your region. The power requirements for the switch are
listed in “Power Specifications” on page 209.

If the switch has AT-SBxPWRSYS1-80 Power Supplies, examine the
LEDs on the power supplies. The power supplies are operating normally
when the DC IN and DC OUT LEDs are solid green and the Fault LED is
off. Possible fault conditions and their solutions are described here:

Fault Condition 1: If the DC IN LED is off, the power supply is not receiving
power, has overheated and been disabled, or has failed and needs to be
replaced. Try the following:



Verify that the On/Off switch on the power supply is in the On
position.



Verify that the DC circuit breaker is on.



Verify that the positive and negative power wires are correctly and
securely connected to the terminal block on the power supply and
circuit breaker.

«
...
199
200
201
202
203
...
»

Содержание AT-FAN08























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-FAN08

Бренд: Eaton Страницы: 2

Celabs Distribution Hub and Receiver

Бренд: Cable Electronics Страницы: 2

Бренд: Manhattan Страницы: 2

Pow-R-Line SPX0361126

Бренд: Eaton Страницы: 584

Бренд: SIIG Страницы: 17

Бренд: Watchguard Страницы: 26

Бренд: KanexPro Страницы: 35

Бренд: C&C TECHNIC Страницы: 2

Бренд: KinAn Страницы: 5

Бренд: Jerguson Страницы: 4

IPES-3424DSFP-2P

Бренд: Lantech Страницы: 26

Бренд: IPGARD Страницы: 15

IMI SENSORS EX686B77

Бренд: PCB Piezotronics Страницы: 63

Бренд: Stahl Страницы: 58

Бренд: TRENDnet Страницы: 2

CUVEO CR-UPS2000

Бренд: Me Страницы: 44

Бренд: QSFPTEK Страницы: 11

Бренд: Novus Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды