Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 220

Страница: 220 / 254

General Maintenance



To Close the Analyzer Chamber

220

5977B Series MSD Operating Manual

To Close the Analyzer Chamber

Procedure

Ensure all the internal analyzer electrical leads are correctly attached. Wiring
is not the same for both the EI and CI sources. (See

“To Connect/Disconnect

Wiring from the EI XTR, SS, and Inert Sources”

on page 197.)

Check the side plate O-ring.

Make sure the O-ring has a

very

light coat of Apiezon L high vacuum grease.

If the O-ring is very dry, it may not seal well. If the O-ring looks shiny, it has
too much grease on it. Refer to the

5977 Series MSD Troubleshooting and

Maintenance Manual

for lubricating instructions.

Swing the analyzer side plate closed.

Ensure the vent valve is closed.

If hydrogen or other flammable or toxic substance is used for carrier gas,

gently

hand-tighten the top thumbscrew on the analyzer side plate.

Pumpdown the MSD. (See

“To Pumpdown the MSD”

on page 139.)

Once the MSD has pumped down, close the left analyzer cover and replace
the window cover.

Tune the MSD.



CAUTION

Do not force the analyzer door when closing, or you may damage the
quadrupole.

WARNING

The top thumbscrew must be fastened if hydrogen (or other hazardous gas) is
being used as the GC carrier gas or if hydrogen is used for the JetClean
system. In the unlikely event of an explosion, it may prevent the side plate
from opening.

CAUTION

Do not overtighten the thumbscrew; it can cause air leaks or prevent
successful pumpdown. Do not use a screwdriver to tighten the thumbscrew.



Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды