Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 244

Страница: 244 / 254

CI Maintenance



To Assemble the CI Source

244

5977B Series MSD Operating Manual

To Assemble the CI Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5 mm (8710-1570)

•

Hex ball driver, 2.0 mm (8710-1804)

•

Wrench, open-end, 10 mm (8710-2353)

Procedure

Refer to the exploded parts view

Figure 80

and the CI source parts list

Table 25

on page 245 while using this procedure.

Assemble the ion focus lens, entrance lens, and lens insulator.

Slide the drawout plate and the drawout cylinder into the source body.

Slide the parts assembled in step 1 into the source body.

Install the setscrew that holds the lenses in place.

Attach the ceramic disk to the repeller and place on top of the source body.

Place the heater block assembly on top of the source body.

Reinstall the dummy filament, and the filament and attach with the
setscrews.





CAUTION

Always wear clean gloves when working in the analyzer chamber to avoid
contamination.

Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды