Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 254

background image

3

Installing Intuvo 9000 GC Columns



To Install the GC/MSD Interface Tip Seal

74

5977B Series MSD Operating Manual

To Install the GC/MSD Interface Tip Seal

Materials needed

•

Interface tip seal (G3870-20542)

•

Tip seal spring (G7005-20024)

•

Knurled tip seal retainer (G3870-20547)

The interface tip seal must be in place for the CI source, the EI XTR source,
and HES. The interface tip seal, spring, and knurled tip seal retainer are not
used with EI SS or Inert source.

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

Procedure

1

Verify that the CI source, EI XTR source, or HES is installed. The tip seal,
spring, and knurled tip seal retainer must not be installed when an EI SS or
Inert source is installed. (See

2

Remove the interface tip seal, spring, and knurled nut retainer from the ion
source storage box. In this order, slide the spring, tip seal, and knurled tip seal
retainer over the column sleeve.

CAUTION

Electrostatic discharges to analyzer components are conducted to the side
board where they can damage sensitive components. Wear a grounded
antistatic wrist strap, and take other antistatic precautions

before

you open

the analyzer chamber.

CAUTION

Always wear clean gloves while handling any parts that go inside the GC or the
analyzer chambers.

«
...
72
73
74
75
76
...
»

Содержание 5977B CI MSD































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5977B CI MSD

Бренд: SAER Elettropompe Страницы: 76

Бренд: WAGNER Страницы: 100

flexoTHERM exclusive VWF 57/4

Бренд: Vaillant Страницы: 20

AquaMax Eco Expert

Бренд: Oase Страницы: 60

Бренд: AquaPRO Страницы: 4

Бренд: Junkers Страницы: 12

Smartmax Series

Бренд: ubbink Страницы: 29

Aquantia KHPMS-BI Series

Бренд: Kaysun Страницы: 40

XC Filter Cartridge EV9613-09

Бренд: Everpure Страницы: 2

Бренд: All-Flo Страницы: 28

Бренд: Jandy Страницы: 72

Бренд: Amtrol Страницы: 2

Бренд: Wacker Neuson Страницы: 208

Бренд: GORMAN-RUPP PUMPS Страницы: 45

Бренд: F.F. Group Страницы: 28

Бренд: Malmbergs Страницы: 12

Larius GHIBLI 10:1

Бренд: Samoa Страницы: 28

Бренд: Noritz Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды