Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 254

background image

5

Operating in EI Mode



Venting the MSD

116

5977B Series MSD Operating Manual

Venting the MSD

The DS guides you through the venting process. It turns off the GC and MSD
heaters and diffusion pump heater or the turbo pump at the correct time. It also
lets you monitor temperatures in the MSD and indicates when to vent the MSD.

The MSD

will

be damaged by incorrect venting. A diffusion pump will

backstream vaporized pump fluid onto the analyzer if the MSD is vented before
the diffusion pump has fully cooled. A turbo pump will be damaged if it is vented
while spinning at more than 50% of its normal operating speed.

For complete venting instructions, see

“To Vent the MSD”

WARNING

Make sure the GC/MSD interface and the analyzer zones are cool (below
100 °C) before you vent the MSD. A temperature of 100 °C is hot enough to
burn skin; always wear cloth gloves when handling analyzer parts.

WARNING

If hydrogen is used as a carrier gas or JetClean system supply, the carrier and
JetClean system supply shutoff valves must be closed before turning off the
MSD power. If the foreline pump is off, hydrogen will accumulate in the MSD
and an explosion may occur. Read

“Hydrogen Safety”

on page 24 before

operating the MSD with hydrogen gas.

WARNING

Never open the vent valve or shut down the vacuum pumps without first
closing the shutoff valves for all hydrogen flows to the analyzer. This includes
hydrogen carrier gas and hydrogen for the JetClean system.

CAUTION

Never vent the MSD by allowing air in through either end of the foreline hose.
Use the vent valve or remove the column nut and column.

Do not vent while the turbo pump is still spinning at more than 50%.

Do not exceed the maximum recommended total gas flow. (See

«
...
114
115
116
117
118
...
»

Содержание 5977B CI MSD































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5977B CI MSD

Бренд: Barnes Страницы: 12

Бренд: A.O. Smith Страницы: 8

Бренд: YGHP Страницы: 14

Бренд: IBC Страницы: 22

Бренд: TapFlo Страницы: 13

Бренд: EINHELL Страницы: 44

Бренд: Carrier Страницы: 12

Бренд: Watts Страницы: 22

Бренд: Graco Страницы: 32

Бренд: Flux Страницы: 80

Бренд: Alpine Страницы: 20

Kaysun Aquantia R-32 PRO

Бренд: Frigicoll Страницы: 44

Optyma Slimpack OP-LSQM Series

Бренд: Danfoss Страницы: 174

Бренд: Mex Страницы: 2

Boiler Performance BOSS 36

Бренд: Manta Страницы: 4

Бренд: WAGNER Страницы: 120

Бренд: Graco Страницы: 32

Бренд: DAB Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды