Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 224

Страница: 224 / 254

CI Maintenance



To Remove the EI HES Radiator

224

5977B Series MSD Operating Manual

To Remove the EI HES Radiator

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Tweezers (8710-2460)

•

T10 Torx screwdriver (5182-3466)

Procedure

Remove the EI HES. (See

“To Remove the EI HES”

on page 178.)

Disconnect the wires from the EI HES radiator. (See

“To Connect/Disconnect

Wiring to the EI HES Radiator”

on page 225.)

Use a T10 Torx screwdriver to loosen the 2 screws that secure the radiator to

the analyzer, and place the radiator in its storage container.



WARNING

The analyzers, GC/MSD interface, and other components in the analyzer
chamber operate at very high temperatures. Do not touch any part until you
are sure it is cool.

CAUTION

•

Always wear clean gloves to prevent contamination when working in the
analyzer chamber.

•

Make sure you use an antistatic wrist strap and take other antistatic
precautions before touching analyzer components.

•

When disconnecting leads, pull on the connectors, not on the wires



Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды