Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 124

Страница: 124 / 254

Operating in EI Mode



To Set the GC/MSD Interface Temperature from MassHunter

124

5977B Series MSD Operating Manual

To Set the GC/MSD Interface Temperature
from MassHunter

Procedure

From

Instrument Control

view select

Instrument>GC Edit Parameters.

Click the

Aux Heaters

icon to edit the interface temperature. (See

Figure 38

Select

to turn on the heater and type the setpoint in the

Value °C

column.



The typical setpoint is 280 °C.

Click

Apply

to download setpoints, or click

to download setpoints and

close the window.

To make the new settings part of the method, select

Save

from the Method menu.

Figure 38 8890 GC edit parameters window

CAUTION

Ensure that the carrier gas is turned on and the column has been purged of air
before heating the GC/MSD interface or the GC oven.

When setting the GC/MSD interface temperature, never exceed the maximum
for your column.

Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды