manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации, Страница: 139 / 254

Поделиться
Скачать
Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 139

5

Operating in EI Mode

To Pumpdown the MSD

5977B Series MSD Operating Manual

139

To Pumpdown the MSD

You can also use the 8890 or 7890B GC control panel to perform this task. (See 
also 

“Operating the MSD from the 7890 GC Control Panel” 

on page 104.)

Procedure

1

Remove the analyzer window cover and open the analyzer cover. (See 

“To 

Open the MSD Covers” 

on page 135.)

2

Verify that the foreline pump inlet valve is open.

3

Verify that the vent valve is open by turning it clockwise until closed. (See 

Figure 47

 on page 140.)

WARNING

Make sure your MSD meets all the conditions listed in the introduction to this 
chapter before starting up and pumping down the MSD. (See 

“Before You Turn 

On the MSD” 

on page 113.) Failure to do so can result in personal injury.

WARNING

Never open the vent valve without first closing the hydrogen supply line to all 
possible sources of hydrogen entry to the analyzer. This requires closing the 
hydrogen shutoff valve to the carrier gas flow module and the shutoff valve to 
the JetClean system supply if either of these hydrogen sources exist on the 
instrument. Read 

“Hydrogen Safety” 

on page 24 before operating the MSD 

with hydrogen gas.

CAUTION

Agilent does not recommend using hydrogen as a carrier gas on systems 
equipped with an IDP3 foreline pump.

WARNING

Do not open the vent valve without verifying that the JetClean system 
hydrogen supply shutoff valve is closed if the optional JetClean system is 
installed. Refer to the JetClean system Operating manual for warnings 
regarding hydrogen safety when the hydrogen shutoff valve is open.

    

             

Содержание 5977B CI MSD































































































































































































































































Отзывы:

Нет отзывов