Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 254

background image

5

Operating in EI Mode



Operating the MSD from the 7890 GC Control Panel

104

5977B Series MSD Operating Manual

Operating the MSD from the 7890 GC Control
Panel

The GC control panel on a 7890A+ or 7890B GC can show the actual
temperature and pressure of the MSD or initiate a task on the MSD without using
the Agilent MassHunter GC/MS Acquisition software. You can access functions,
such as venting and setting temperatures, right from the GC control panel.
Limited features are available from the GC control panel. The Agilent
MassHunter GC/MS Acquisition software is the full-featured controller for most
instrument control operations.

MSD designated key on the GC control panel

The

MS/Aux Det

key on the 7890B GC control panel allows access to control and

configuration parameters on the MSD. (See

.) For 7890A+ models with

updated firmware, this key is labeled

Aux Det #

which can be substituted for the

MS/Aux Det

key in the procedures that follow.

Figure 27 7890B GC control panel

«
...
102
103
104
105
106
...
»

Содержание 5977B CI MSD































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5977B CI MSD

Бренд: Wacker Neuson Страницы: 38

Бренд: Quooker Страницы: 12

Бренд: EINHELL Страницы: 44

Бренд: BLACKMER Страницы: 12

GOULDS e-SVI Series

Бренд: Xylem Страницы: 40

Gyre 300 Series

Бренд: Maxspect Страницы: 164

Бренд: Wacker Neuson Страницы: 64

Бренд: F.F. Group Страницы: 28

Бренд: Dantherm Страницы: 17

Бренд: Kärcher Страницы: 68

Бренд: clage Страницы: 24

Flojet RLFP122202A

Бренд: Xylem Страницы: 40

Altherma EHYHBH05A Series

Бренд: Daikin Страницы: 264

Бренд: A.O. Smith Страницы: 24

ARO PF20 B Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: KNF Страницы: 56

FLOJET BW5000 Series

Бренд: Xylem Страницы: 8

Бренд: Rinnai Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды