manualshive.com logo in svg

Agilent Technologies 1670G Series, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies 1670G Series Скачать руководство пользователя страница 3

The oscilloscope option includes the following features:

•

2 GSa/s digitizing for 500 MHz bandwidth single shot oscilloscope

•

>32000 samples per channel

•

Automatic pulse parameters displays time between markers, acquires until
specified time between markers is captured, performs statistical analysis on time
between markers

•

Lightweight mini probes

Service Strategy

The service strategy for this instrument is the replacement of defective assemblies.
This service guide contains information for finding a defective assembly by testing
and servicing the Agilent 1670G-series logic analyzers.

This logic analyzer can be returned to Agilent for all service work, including
troubleshooting.  Contact your nearest Agilent Technologies Sales Office for details.

Agilent Technologies 1670G-Series Logic Analyzer

iii

Содержание 1670G Series

































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды