Aerco 5R5-384 Скачать руководство пользователя страница 93

Страница: 93 / 139

AERCO Control System (ACS)

APPENDIX B:

Status and Fault Messages

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 93 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

TABLE B-2: C-More Status and Fault Messages

Code

Message

Description

PRG SWTCH OPEN
DURING PURGE

The Purge Position Limit switch on the Air/Fuel valve
opened during purge.

IGN SWTCH OPEN
DURING IGNITION

The Ignition Position Limit switch on the Air/Fuel valve
opened during ignition.

AIRFLOW FAULT
DURING IGN

The Blower Proof Switch opened during ignition.

AIRFLOW FAULT
DURING RUN

The Blower Proof Switch opened during run.

SSOV FAULT
DURING IGN

The SSOV switch closed or failed to open during ignition.

SSOV FAULT
DURING RUN

The SSOV switch closed for more than 15 seconds during
run.

FLAME LOSS
DURING IGN

The Flame signal was not seen during ignition or lost within
5 seconds after ignition.

FLAME LOSS
DURING RUN

The Flame signal was lost during run.

HIGH EXHAUST
TEMPERATURE

The High Exhaust Temperature Limit Switch is closed.

LOSS OF POWER

A power loss occurred. The time and date when power
was restored is displayed.

LOSS OF SENSOR

Not Currently Used

LOSS OF SIGNAL

Not Currently Used

HIGH O2 LEVEL

Not Currently Used

LOW O2 LEVEL

Not Currently Used

HIGH CO LEVEL

Not Currently Used

SSOV RELAY FAILURE

A failure has been detected in one of the

relays that control the

SSOV.

RESIDUAL
FLAME

The Flame signal was seen for more than 60 seconds
during standby.

HEAT DEMAND
FAILURE

The Heat Demand Relays on the Ignition board failed to
activate when commanded.

IGN SWTCH CLOSED
DURING PURGE

The Ignition Position Limit switch on the Air/Fuel valve
closed during purge.

PRG SWTCH CLOSED
DURING IGNITION

The Purge Position Limit switch on the Air/Fuel valve
closed during ignition.

SSOV SWITCH OPEN

The SSOV switch opened during standby.

Содержание 5R5-384












































































































































Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды

Aerco 5R5-384, Руководство пользователя

Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды