Aerco 5R5-384 Скачать руководство пользователя страница 3

Страница: 3 / 139

AERCO Control System (ACS)

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 3 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

2.12 RELAY WIRING ............................................................................................................32

2.12.1 System Start Relay .............................................................................................33

2.12.2 Fault Alarm Relay ...............................................................................................33

2.12.3 Auxiliary Relay ....................................................................................................33

2.13 4-20 MA WIRING ..........................................................................................................33

2.14 MOUNTING & WIRING THE OPTIONAL ACS RELAY BOX

..........................................................33

2.15 RELAY PANEL INSTALLATION AND WIRING ...........................................................34

2.16 RELAY PANEL COMPONENTS...................................................................................39

2.16.1 Power .................................................................................................................39

2.16.2 Inputs..................................................................................................................39

2.16.3 Outputs ...............................................................................................................39

2.17 RELAY PANEL OPERATION .......................................................................................40

2.18 ACS PROGRAMMING FOR USE WITH THE ACS RELAY PANEL

.................................................41

2.17.

.........................................................................................................................41

2.18.1 RS485 Menu Settings for Relay Panel Programming ..........................................41

2.18.2 Configuration Menu - Relay Panel Settings ........................................................41

CHAPTER 3: OPERATION ................................................................................. 43

3.1 INTRODUCTION .............................................................................................................43

3.2 FRONT PANEL OPERATING CONTROLS AND DISPLAYS .........................................43

3.3.1 Menu Processing Procedure .................................................................................45

3.3 OPERATING MENU .......................................................................................................47

3.4.1 Header Temp and Percent of Load .......................................................................47

3.4.2 HEADER SETPOINT ............................................................................................47

3.4.3 OUTSIDE AIR TEMP ............................................................................................48

3.4.4 I/O STATUS .........................................................................................................48

3.4.5 RETURN TEMP ....................................................................................................48

3.4.6 NETWORK BOILER OUTLET TEMPERATURE ...................................................48

3.4.7 NETWORK BOILER ERROR CODE ....................................................................48

3.4 SETUP MENU.................................................................................................................49

3.5.1 ENTER PASSWORD ............................................................................................49

3.5.2 DATE AND TIME MENU OPTIONS ......................................................................49

3.5 RS232 MENU .................................................................................................................49

3.6.1 RS232 MODE .......................................................................................................49

3.6.2 RS232 BAUD RATE .............................................................................................49

3.6.3 MODBUS ADDRESS ............................................................................................50

3.6.4 NETWORK TIMEOUT ..........................................................................................50

3.6.5 MODBUS PASS THRU ........................................................................................50

3.6 RS485 (MODBUS) MENU ..............................................................................................50

3.7.1 RS485 BAUD RATE .............................................................................................50

Содержание 5R5-384












































































































































Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды

Aerco 5R5-384, Руководство пользователя

Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды