Aerco 5R5-384 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 139

background image

AERCO Control System (ACS)

CHAPTER 3

: Operation

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 51 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

terminals. Up to 32 Boilers can be connected to the Network (default = 02).

3.7.5 MODBUS CNTL TYPE

This menu option sets the Modbus Control Type to

ROUND ROBIN

or

BROADCAST

. Only

ROUND ROBIN

can be used at this time. When set to ROUND ROBIN, each networked boiler

is addressed individually in sequence.

BROADCAST

is currently not used for the ACS.

3.7.6 NETW BOILER Xx ADDRESS=Yyy

Up to 32 Network Boilers can be accommodated on the Modbus Network (Where Xx = 01 – 32
and Yyy = 001 – 127). Each Boiler must be assigned a unique address on the network ranging
from 001 to127. No addresses should be entered if automatic boiler detection is desired. Simply
set the

MIN SLAVE ADDR

and

MAX SLAVE ADDR

to the minimum and maximum address

range of the boilers. To program boiler addresses in the order you desire, enter them here and
set the

MIN SLAVE ADDR

and

MAX SLAVE ADDR

to zero.

FIELD ADJUST MENU

3.7

The

FIELD ADJUST MENU

contains the most extensive list of options compared to the other 8

Menu categories. The options in this menu allow you to adjust important parameters to suit the
specific needs of your ACS installation. Included are options to select the Header Mode and
Temperature Limits, Internal Setpoint, Building Reference Temperature, Reset Ratio and
Remote Signal. In addition, the Field Adjust Menu contains a series of options which can be
used to set up a Header Setpoint Offset Schedule for an entire week. Descriptions of the Field
Adjust Menu options:

3.8.1 HEADER SET MODE

The

HEADER SET MODE

option sets the Header Setpoint selection method for the ACS.

Allowable selections are: CONSTANT SETPT, OUTDOOR RESET or REMOTE SETPT.
(Default = CONSTANT SETPT).

3.8.2 HDR HIGH LIMIT

The

HDR HIGH LIMIT

option sets the maximum temperature setting allowed for the Header

Setpoint. This setting also defines the 20 mA temperature equivalent when operating in the
Remote Setpoint Mode using a 4 – 20 mA signal. The allowable setting range is from the

HDR

LOW LIMIT

to 220°F. (Default = 200°F).

3.8.3 HDR LOW LIMIT

The

HDR LOW LIMIT

menu option sets the minimum temperature setting allowed for the

Header Setpt. This setting also defines the 4 mA temperature equivalent when operating in the
Remote Setpoint Mode using a 4 – 20 mA signal. The setting range is from 40°F to the

HDR

HIGH LIMIT

. (Default = 40°F).

3.8.4 INTERNAL SETPT

The

INTERNAL SETPT

temperature is the

HEADER SETPT

used when

CONSTANT SETPT

is

selected for the

HEADER SET MODE

or when the ACS operates in the Failsafe Mode and

CONSTANT SETPT

is selected as the FAIL SAFE MODE setting in the Configuration Menu.

«
...
49
50
51
52
53
...
»

Содержание 5R5-384












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5R5-384

Бренд: C&K systems Страницы: 2

Бренд: U-Prox Страницы: 31

Бренд: Eaton Страницы: 86

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: QCON Страницы: 4

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: VAT Страницы: 27

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды