Aerco 5R5-384 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 139

background image

AERCO Control System (ACS)

CHAPTER 4

: Programing ACS Operating Modes

Page 78 of 139

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

11/22/2017

GF-131

Phone: 800-526-0288

OMM-0081_0F

The ACS will continuously poll the boilers at prescribed intervals. Therefore, if a boiler is placed
off-line and then placed back on-line, it will again be recognized by the ACS during the next
polling cycle.

TESTING THE SYSTEM USING THE C-MORE CONTROLS

4.8

The following procedure places a load on the system and will begin firing the boilers. At this
point it is very important to make sure the system pumps are running. After system has been
initialized as described in

paragraph 4.5

, proceed as shown in

Instruction 4.8

on next page:

IMPORTANT!

Prior to performing these tests, view and record the PRESENT settings stored in the ACS for

HEADER SET MODE

and

INTERNAL SETPT.

These settings are located in the Field Adjust

Menu and MUST be restored to these values upon completion of following tests.

NOTE

On a cold start up, if the system is designed with a return temperature
sensor with the intent to activate the plant Delta-Temperature (Delta-T)
Limit function, consider disabling the return sensor. During a cold start, the
cold water may be cold enough to trip the High Delta-T alarm and shut
down the plant. In this case you can set the Return Sensor Mode to OFF to
temporarily disable the Plant Delta-T function and then set it to NORMAL
after the return water has warmed up.

Testing the System Using the C-More Controls

1.

Turn off the ACS by pressing the ON/OFF key. The ON LED will turn off.

2.

Using the MENU key, select the

FIELD ADJUST MENU

and scroll to the

HEADER SET

MODE

option, The second line of the display will show the current setting stored in

memory (

CONSTANT SETPT, OUTDOOR RESET,

or

REMOTE SETPT).

3.

If

CONSTANT SETPT

is not currently selected, press the CHANGE key. Select the

CONSTANT SETPT

mode using the ▲ or ▼ arrow key. When selected, store the

change by pressing the ENTER key.

4.

Next, scroll to the

INTERNAL SETPT

menu option. The second line of the display will

show the current Internal Setpoint temperature (°F) stored in memory.

5.

Press the CHANGE key. Set the

INTERNAL SETPT

temperature to 180°F using the ▲

and ▼ arrow keys. When set, store the change by pressing the ENTER key.

6.

Turn on the ACS by pressing the ON/OFF key. The ON indicator will light and the boiler
plant will start to operate.

7.

Using the MENU key on the ACS, scroll to the OPERATING MENU. The first line of the
display will show the Header Temperature. The second line of the display will show the
Firing Rate % and the number of Units (boilers) firing.

8.

When all boilers have reached at least a 55% firing rate, any boilers that have not
started have not been identified by the ACS. (Cont.)

«
...
76
77
78
79
80
...
»

Содержание 5R5-384












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5R5-384

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 34

Бренд: NCR Страницы: 6

Бренд: Handicare Страницы: 56

Бренд: Valor Страницы: 20

Бренд: IDK Страницы: 96

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Smart Control Panel 880RGD

Бренд: Raynor Страницы: 4

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

Бренд: S&C Страницы: 26

Бренд: Barton Страницы: 36

Бренд: TWR Lighting Страницы: 49

Бренд: U-Tron Страницы: 8

Бренд: Agilent Technologies Страницы: 20

Бренд: Keurig Страницы: 2

Бренд: FOR-A Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды