Aerco 5R5-384 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 139

background image

AERCO Control System (ACS)

CHAPTER 3

: Operation

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 61 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

3.12.4 AUX RELAY OPEN

The

AUX RELAY OPEN

setting is the Percent Level output below which the AUX Relay will

open if it was closed due to the conditions described by the AUX RELAY CLOSE setting.

3.12.5 AUX RELAY CLOSE

This determines the condition for which the AUX relay will close. If 100% FIRE RATE is
selected, the AUX relay will close when all available boilers are firing at 100%. If 100% AND
OFF (default) is selected, it will close when all available boilers are firing at 100% as well as
when no boilers are available and the boiler plant is below setpoint. This relay can trigger
emergency heat in the latter case.

3.12.6 FAULT ALRM RELAY

This setting tells the ACS which faults should activate the fault alarm relay. The default is

ALL

FAULTS

. If

NO INTERLOCK

is selected, the Fault Alarm Relay will not activate when the

interlocks are opened, however the ACS will still shut down all boilers. If

INTERLOCK 2

is

selected, the Fault Alarm Relay will only activate when Interlock 2 is opened and not when
Interlock 1 is opened. Similarly, when

INTERLOCK 1

is selected, the fault alarm relay will only

activate when Interlock 1 is opened and not when Interlock 2 is opened.

3.12.7 FAULT ALARM BLRS

This selection tells the ACS whether to activate the fault alarm relay if a boiler connected to it is
faulted.

3.12.8 FAULT ALRM CLEAR

Selecting MANUAL will latch the fault alarm relay if a fault condition occurs and goes away. The
CLEAR key must be pushed to deactivate the relay. If set to AUTOMATIC, the fault relay will
open when the fault condition goes away.

CALIBRATION MENU

3.12

The options contained in this Menu should only be used by factory-trained personnel, since it
contains options that could adversely affect system operation if incorrectly set.

NOTE

The Level 2 Password (

6817

) must be entered in order to view or

change options in the Calibration Menu.

3.13.1 HDR SENS OFFSET

This option sets the offset temperature value that is added to the displayed Header Sensor
temperature in the event that it is different from a trusted reference Header temperature reading
and needs calibration. Be sure the Header Sensor is properly installed before adjusting this
offset value. The allowable offset range is ±10°F

3.13.2 OUTD SENS OFFSET

This offset value is added to the Outdoor Sensor temperature displayed in case it is different
from a trusted reference outdoor temperature reading and needs calibration. Be sure the
Outdoor sensor is properly installed before adjusting this value. The allowable offset range is
±10°F.

«
...
59
60
61
62
63
...
»

Содержание 5R5-384












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5R5-384

Бренд: Quickmill Страницы: 3

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: UCS Страницы: 4

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: Vag Страницы: 12

Бренд: I-Tork Страницы: 15

Бренд: MGC Страницы: 16

FAREX SR MINI SYSTEM

Бренд: RKC INSTRUMENT Страницы: 82

Бренд: SeaLevel Страницы: 115

Бренд: SACH Страницы: 99

Бренд: Wenglor Страницы: 44

Бренд: ShoreStation Страницы: 19

Бренд: EOS Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды