Aerco 5R5-384 Скачать руководство пользователя | Manualshive

Страница: 20 / 139

background image

AERCO Control System (ACS)

CHAPTER 2

: ACS Installation

Page 20 of 139

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

11/22/2017

GF-131

Phone: 800-526-0288

OMM-0081_0F

PROBE DEPTH MUST

EXTEND AT LEAST 2"

INTO PIPE

WELDED 1/2"

COUPLING OR

4"x4*x1/2"

T - FITTING

HEADER SENSOR

WITH THERMOWELL

INSTALLED

Figure 2-3: Header Sensor Installation Details

2.5.3 Outdoor Air Sensor Installation

The Outdoor Air Temperature Sensor (P/N GP-122662) is required when operating in the ACS
in the Outdoor Reset Mode (paragraph 4.2). An Outdoor Air Sensor Kit (P/N GM-122781) is also
available. This kit contains the Sensor (GP-122662) and a Mounting Bracket for wall mounting.
The Outdoor Air Sensor should be mounted on the North side of the building, shielded from
direct sunlight, and away from air intakes or outlets from the building. Shielded pair 18 AWG
cable (Belden # 8760 or equiv.) is recommended for sensor wiring. The Outdoor Air Sensor can
be mounted up to 600 feet from the ACS. See instructions below.

NOTE

The Outdoor Air Sensor is a thermistor type sensor. The Resistance
vs. Temperature Chart for this sensor is provided in Appendix E.
Length of Header Sensor wire leads should not exceed 600 feet.

Installing the Outdoor Air Sensor

1.

Refer to Figure 2-4 for a typical Outdoor Air Sensor installation.

2.

Attach the sensor to the mounting bracket and secure the bracket in a suitable location on
the North side of the building.

3.

Using shielded pair cable (Belden #8760 or equiv.), connect the two Sensor leads to
terminals 1 and 2 on the ACS. There is no polarity to observe when connecting the sensor.

4.

Terminate the cable shield at SHLD terminal 3 of the ACS. DO NOT terminate the shield at
the Sensor end of the cable.

«
...
18
19
20
21
22
...
»

Содержание 5R5-384












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5R5-384

Бренд: zipwake Страницы: 12

Бренд: Watts Страницы: 2

Бренд: jbc Страницы: 12

Бренд: jbc Страницы: 4

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Wavelink Страницы: 69

Бренд: Campbell Страницы: 72

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Hard Top Lifter

Бренд: Garage Smart Страницы: 20

Бренд: S&P Страницы: 17

Бренд: S&S Northern Страницы: 9

Бренд: Yamaha Страницы: 92

Бренд: Linak Страницы: 33

LMT070DICFWD-NJN

Бренд: Topway Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды