Aerco 5R5-384 Скачать руководство пользователя страница 94

Страница: 94 / 139

AERCO Control System (ACS)

APPENDIX B:

Status and Fault Messages

Page 94 of 139

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

11/22/2017

GF-131

Phone: 800-526-0288

OMM-0081_0F

TABLE B-2: C-More Status and Fault Messages

Code

Message

Description

IGNITION BOARD COMM
FAULT

Communication fault between the Ignition board and the
CPU board.

DIRECT DRIVE
SIGNAL FAULT

The direct drive signal is not present or is out of range.

REMOTE SETPT
SIGNAL FAULT

The remote setpoint signal is not present or is out of range.

OUTDOOR TEMP
SENSOR FAULT

The temperature measured by the Outdoor Air Sensor is
out of range.

OUTLET TEMP
SENSOR FAULT

The temperature measured by the Outlet Sensor is out of
range.

FFWD TEMP
SENSOR FAULT

The temperature measured by the FFWD Sensor is out of
range.

HIGH WATER
TEMPERATURE

The temperature measured by the Outlet Sensor exceeded
the Temp Hi Limit setting.

LINE VOLTAGE
OUT OF PHASE

The High AC voltage is out of phase from the low AC
voltage.

STEPPER MOTOR
FAILURE

The stepper motor failed to move the valve to the desired
position.

SETPT LIMITING ACTIVE

Setpoint temperature has exceeded the maximum
allowable setting.

MODBUS COMM FAULT

The RS485 (Modbus) network information is not present or
is corrupted.

BOILER_RETRY_WAIT_
MESSAGE

BOILER_FAULT_PURGE_
MESSAGE,

BOILER_RETRY_PAUSE_
MESSAGE

EXHAUST_TEMP_SENSOR_
SHORT_MESSAGE

EXHAUST_TEMP_SENSOR_
OPEN_MESSAGE

EXHAUST_TEMP_HIGH_
WARNING_MESSAGE

EXHAUST_TEMP_HIGH_
FAULT_MESSAGE

INLET_TEMP_SENSOR_
SHORT_MESSAGE

Содержание 5R5-384












































































































































Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды

Aerco 5R5-384, Руководство пользователя

Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды