Aerco 5R5-384 Скачать руководство пользователя | Manualshive

Страница: 33 / 139

background image

AERCO Control System (ACS)

CHAPTER 2

: ACS Installation

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 33 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

NOTE

The state of the SYS START, FLT ALARM and AUX Relays are
controlled by options contained in the Relay Menu described in
Chapter 3, paragraph 3.11.

2.12.1 System Start Relay

The state of the System Start (SYS START) relay contacts are controlled by the value set for
the SYS START TEMP and SYS START OPTION in the Relay Menu. The contacts are closed
either when the outdoor air temperature is less than the System Start Temperature (SYS
START TEMP) or when there is a load, or both. The default value for this temperature setting is
70°F. See paragraph 4.5 for additional information.

2.12.2 Fault Alarm Relay

The state of the Fault Alarm (FLT ALARM) relay contacts are controlled by the option selected
for the FAULT ALRM RELAY, FAULT ALARM BLR and FAULT ALRM CLEAR in the Relay
Menu. Contact closure can be set to: ALL FAULTS, NO INTERLOCK, INTERLOCK 2 or
INTERLOCK 1. The default for this option is ALL FAULTS.

2.12.3 Auxiliary Relay

The state of the Auxiliary (AUX) relay contacts are controlled by the AUX RELAY CLOSE and
AUX RELAY OPEN options selected in the Relay Menu. Contact closure can be set to occur
either when all available boilers are at the 100% Fire Rate or for either when all boilers are at
100% Fire Rate or no boilers are available (all boilers faulted or turned off).

4-20 MA WIRING

2.13

The ACS can accept a remote 4 – 20 mA current signal representing a setpoint. This input is
fused internally at 0.63A. Connect the signal leads to the 4-20 + and 4–20 – terminals. Refer to
Chapter 4, paragraph 4.3 for Remote Setpoint programming using a 4 -20 mA input.

MOUNTING & WIRING THE OPTIONAL ACS RELAY BOX

2.14

The ACS (AERCO Control System) Relay Panel is used in combination with the ACS to control
up to 2 isolation valves, boiler interlocks, and a Domestic Hot Water (DHW) pump in a
Combination heating plant where AERCO boilers are bring used for both Building Heat and
Domestic Hot Water heating.

Figure 2-13: AERCO Control System (ACS) Relay Box

«
...
31
32
33
34
35
...
»

Содержание 5R5-384












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5R5-384

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: RAPIBREW Страницы: 16

Бренд: TCS Страницы: 16

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Бренд: East Coast Datacom Страницы: 14

Бренд: Radial Engineering Страницы: 12

Бренд: Hach Страницы: 504

Бренд: FrSky Страницы: 2

RC Electronic DPSI LCD

Бренд: Emcotec Страницы: 32

Бренд: Velleman Страницы: 22

Бренд: National Instruments Страницы: 27

Бренд: Vaniman Страницы: 2

Бренд: Ultraflex Страницы: 48

5400 Pilot Operated

Бренд: Valve Concepts Страницы: 18

Бренд: Danfoss Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды