Aerco 5R5-384 Скачать руководство пользователя страница 5

Страница: 5 / 139

AERCO Control System (ACS)

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 5 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

3.11.1 PROPORTIONAL BND .......................................................................................58

3.11.2 INTEGRAL GAIN ................................................................................................59

3.11.3 DERIVATIVE GAIN .............................................................................................59

3.11.4 Decreasing Boiler Cycles ....................................................................................59

3.11.5 HI_DB_SETPT_EN (High Deadband Setpoint Enable) .......................................59

3.11.6 DEADBAND HIGH ..............................................................................................59

3.11.7 DEADBAND LOW ..............................................................................................59

3.11.8 SETPT DOWN RATE (Setpoint Down (descending) Rate ..................................60

3.11.9 DEMAND OFFSET .............................................................................................60

3.11 RELAY MENU ..............................................................................................................60

3.12.1 SYS START TEMP .............................................................................................60

3.12.2 SYS START OPTION .........................................................................................60

3.12.3 SYS START INTLK .............................................................................................60

3.12.4 AUX RELAY OPEN ............................................................................................61

3.12.5 AUX RELAY CLOSE ..........................................................................................61

3.12.6 FAULT ALRM RELAY .........................................................................................61

3.12.7 FAULT ALARM BLRS .........................................................................................61

3.12.8 FAULT ALRM CLEAR ........................................................................................61

3.12 CALIBRATION MENU ..................................................................................................61

3.13.1 HDR SENS OFFSET ..........................................................................................61

3.13.2 OUTD SENS OFFSET ........................................................................................61

3.13.3 4 - 20 MA OFFSET .............................................................................................62

3.13.4 RETN SENS OFFSET ........................................................................................62

3.13.5 RAMP UP % / MIN ..............................................................................................62

3.13.6 RAMP DOWN % / MIN .......................................................................................62

3.13.7 RESET DEFAULTS ............................................................................................62

3.13.8 PASSTHRU WRITE ............................................................................................63

3.13.9 VALVE WAIT TIME .............................................................................................63

3.13.10 SYSTEM OVERRIDE (Modbus Enable/Disable) ...............................................63

3.13 ACS QUICK-START GUIDE MENU .............................................................................63

3.14.1 CONSTANT SETPT MODE (Default): ................................................................64

3.14.2 REMOTE SETPT MODE: ...................................................................................65

3.14.3 OUTDOOR RESET MODE .................................................................................66

CHAPTER 4:

PROGRAMMING ACS OPERATING MODES ............................... 67

4.1 INTRODUCTION .............................................................................................................67

4.2 OUTDOOR RESET MODE .............................................................................................67

4.2.1 Selecting Outdoor Reset Mode .............................................................................68

4.2.2 Determining Reset Schedule ................................................................................68

4.2.3 Entering Reset Ratio and Building Reference Temperature ..................................69

4.2.4 SELECTING BOILER OPERATING MODE ..........................................................69

4.2.5 Entering System Start Temperature ......................................................................70

4.2.6 Entering Boiler Start and Boiler Stop Levels .........................................................70

Содержание 5R5-384












































































































































Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды

Aerco 5R5-384, Руководство пользователя

Результаты поиска

Содержание 5R5-384

Отзывы:

Похожие инструкции для 5R5-384

Бренды по названию

Популярные бренды