Aerco 5R5-384 Скачать руководство пользователя | Manualshive

Страница: 115 / 139

background image

AERCO Control System (ACS)

APPENDIX G:

Programming Using RS232 Communication

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 115 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

G.3 RS232 COMMUNICATION SET-UP

Regardless of the terminal emulation utilized, the following guidelines must be adhered to when
interfacing the ACS to the Terminal device:

RS232 Communication Set-Up

1.

Connect cable leads to the RS-232 connector in the wiring area of the ACS.

2.

Connect the free end of the cable to the COM 1 or COM 2 port on your laptop, or other
suitable terminal device.

3.

Set up the emulator communication link as follows:

a. Set the baud rate to 9600.

b. Set the data format to 8 bits, 1 stop bit, no parity and either Xon/Xoff or No Flow

Control.

4.

Turn on the ACS by pressing the ON/OFF key. Verify that the ON LED lights.

5.

Press the MENU key. Go to the SETUP MENU and enter a valid PASSWORD.

6.

Press the MENU key and go to the RS232 MENU.

7.

Press the ▲ arrow key to display the

RS232 MODE

option.

8.

Press the ▲ or ▼ arrow key to display

NORMAL

. Press the ENTER key to store the

NORMAL

selection

9.

Start the emulator software program.

10.

At the command prompt, enter the password EXACTLY as follows (case-sensitive):

P=gobms

11.

Press Return (<Rtn>) on your terminal.

12.

The setup is now complete. You are ready to begin viewing or changing ACS functions.

G.4 PROGRAMMING PROCEDURE

ACS functions which can be viewed or changed are listed in

Table G-1

along with their

corresponding command numbers. Functions which can only be viewed (such as actual sensor
readings) are marked “Read Only”. Viewing or changing function values is accomplished as
follows:

Programming Procedure

1.

Select the number of the desired command from Table J-1.

2.

To view a parameter, type

?

, followed by the command number and then press return

(<Rtn>). For example, to view command no. 00 (HEADER TEMPERATURE), enter:

?00<Rtn>

The header temperature reading will be displayed. All temperature readings are in °F.

3.

To program (set) a ACS parameter, type @, followed by the command number, an equal
sign, the parameter value and a trailing zero. For example, to set command 05
(SYSTEM OUTSIDE AIR START TEMPERATURE) to 65°F, enter:

@05=650<Rtn>

«
...
113
114
115
116
117
...
»

Содержание 5R5-384












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5R5-384

Бренд: IBM Страницы: 105

Бренд: Federal Signal Corporation Страницы: 34

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренд: Harmonic Drive Страницы: 85

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: RADVision Страницы: 39

Бренд: QNAP Страницы: 35

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: Dantherm Страницы: 20

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды