Advance acoustic 908 7161 020 Скачать руководство пользователя страница 58

Страница: 58 / 67

ENGLISH

SERVICE MANUAL

9096982000(1)2007-02

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

ELECTRICAL SYSTEM

BRUSH MOTOR ELECTROMAGNETIC SWITCH DISASSEMBLY/ASSEMBLY

Disassembly

Disconnect the battery connector (12).

Move aside the recovery water drain hose (16).

Remove the battery charger cable (6) from the cable holder (7).

Remove the screws (A) and carefully move aside the panel (B) by disengaging the cable grommet (C) from its housing on

the panel (B).

Disconnect the connectors (D), (E), (F), and remove the panel (B).

Disconnect the terminals (G) and (H) from the electromagnetic switch (J). Disconnect also the terminals (I), which are

present only on the models with drive system.

Remove the screws (K) and move the electrical panel (L) by disengaging it from the lower fastener (M).

Remove the screws (N) on the rear side of the electrical panel (L), then remove the electromagnetic switch (J).

Assembly

Assemble the components in the reverse order of disassembly.

L K

S301571A

S301572A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды