Advance acoustic 908 7161 020 Скачать руководство пользователя страница 49

Страница: 49 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

DRIVE SYSTEM

DRIVE SYSTEM MOTOR ELECTRICAL INPUT CHECK (For Adfinity

20 D, X 20 D, X 20 C, X 24 D)

WARNING!

This procedure must be performed by qualified personnel only and with the help of an assistant.

Check that the batteries are completely charged, otherwise charge them as shown in the User Manual.

If the tank (21) contains recovery water:

Drive the machine to the appointed recovery water disposal area.

Turn the ignition key (80) to “0”.

Empty the recovery water tank (21) with the hose (16).

Drive the machine on a level floor.

Lower the deck by pressing the pedal (11).

Under the left side the machine, install a suitable jack (C) in the position (A), and slightly lift the machine so that the left

wheel (C) can turn freely, without touching the floor or the jack.

WARNING!

While performing this procedure, pay attention to the rotation of the driving wheel (C).

Apply the amperometric pliers (D) on one cable (E) of the drive system motor.

Turn the ignition key (80) to “I”.

Turn the speed adjuster (84) to the maximum speed.

With the help of an assistant who firmly keeps the machine by the handlebar, push the drive paddle (3) completely forward

and check that the electrical input is 1.5 - 2.5 A at 24 V. Release the drive paddle (3). Turn the ignition key (80) to “0” and

remove the amperometric pliers (D).

If the electrical input is higher, perform the following procedures to detect and correct the abnormal input:

Check if there is dust or debris preventing the component rotation. The lifted wheel (C) must turn freely whit a slight

resistance of the differential.

If necessary, disassemble the motor-differential (see the procedure in the relevant paragraph) then check for hub

correct alignment and bearing smooth running.

If the above-mentioned procedures do not lead to a correct electrical input, the motor must be replaced

(see the procedure in the relevant paragraph).

Perform steps 4 and 5 in the reverse order.

•

10.

S301562A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды