Advance acoustic 908 7161 020 Скачать руководство пользователя страница 5

Страница: 5 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

GENERAL INFORMATION

CONVENTIONS

Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say in driving position

with the hands on the handlebar.

MACHINE LIFTING

WARNING!

Do not work under the lifted machine without supporting it with safety stands.

MACHINE TRANSPORTATION

WARNING!

Before transporting the machine, make sure that:

All covers are closed.

The ignition key is removed.

The machine is securely fastened to the means of transport.

–

OTHER REFERENCE MANUALS

The following manuals are available at Nilfisk-Advance Literature Service Department:

Adfinity

17 ST - 20 ST: User Manual - Form Number 9096912000

Adfinity

17 ST - 20 ST: Spare Parts List - Form Number 9096913000

Adfinity

20 D - X 20 D - X 20 C - X 24 D: User Manual - Form Number 9096910000

Adfinity

20 D - X 20 D - X 20 C - X 24 D: Spare Parts List - Form Number 9096911000

SAFETY

The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary

precautions to safeguard people and property.

SYMBOLS

DANGER!

It indicates a dangerous situation with risk of death for the operator.

WARNING!

It indicates a potential risk of injury for people or damage to objects.

CAUTION!

It indicates a caution related to important or useful functions.

Pay careful attention to the paragraphs marked by this symbol.

NOTE

It indicates a remark related to important or useful functions.

CONSULTATION

It indicates the necessity to refer to the User Manual before performing any procedure.

GENERAL INSTRUCTIONS

Specific warnings and cautions to inform about potential damages to people and machine are shown below.

DANGER!

This machine must be used by properly trained and authorised personnel only. Children or disabled

people cannot use this machine.

Do not wear jewels when working near electrical components.

Do not work under the lifted machine without supporting it with safety stands.

Do not operate the machine near toxic, dangerous, flammable and/or explosive powders, liquids or

vapours.

Disconnect the batteries before performing any maintenance/repair procedure.

Keep the battery far from sparks, flames and incandescent material. During the normal operation

explosive gases are released.

Battery charging produces highly explosive hydrogen gas. Keep the tanks lifted during battery charging

and perform this operation in well-ventilated areas and away from bare flames.

–

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды